Installation๎Notices๎for๎the๎M.2๎and๎SATA๎Connectors:
The availability of the SATA connectors may be affected by the type of device installed in the M.2 connector.
The๎M2A๎connector๎shares๎bandwidth๎with๎the๎SATA3๎1๎connector.๎Refer๎to๎the๎following๎table๎for๎details.
SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5
M.2 SATA SSD
a
r
a a a a
M.2 PCIe SSD
a a a a a a
No๎M.2๎SSD๎Installed
a a a a a a
a: Available, r:๎Not๎available
Connector
Type of
M.2 SSD
7) M2A๎(M.2๎Socket๎3๎Connector)
๎ The๎M.2๎connector๎supports๎M.2๎SATA๎SSDs๎or๎M.2๎PCIe๎SSDs๎and๎support๎RAID๎con๎ฟguration.๎Please๎
note๎that๎an๎M.2๎PCIe๎SSD๎cannot๎be๎used๎to๎create๎a๎RAID๎set๎with๎a๎SATA๎hard๎drive.๎To๎create๎a๎RAID๎
array๎with๎an๎M.2๎PCIe๎SSD,๎you๎must๎set๎up๎the๎con๎ฟguration๎in๎UEFI๎BIOS๎mode.๎Refer๎to๎Chapter๎3,๎
"Con๎ฟguring๎a๎RAID๎Set,"๎for๎instructions๎on๎con๎ฟguring๎a๎RAID๎array.
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole
for๎the๎M.2๎SSD๎to๎be๎installed๎and๎then๎screw๎the๎nut๎๎ฟrst.
Step 2:
Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it with the screw.
Select the proper hole for the M.2 SSD to be installed and refasten the screw and nut.
F_USB30
F_๎U๎๎๎๎๎๎
๎B_๎๎๎ ๎
F_๎ ๎๎๎๎๎๎๎๎ F_๎ ๎๎๎๎
๎๎๎๎๎๎๎๎๎
๎๎๎๎_๎๎๎
๎๎๎๎๎๎B๎
B๎๎S_๎๎
๎๎๎๎๎๎B๎
S๎B_๎๎๎
๎๎๎๎๎๎B๎
๎๎๎_๎๎๎S
๎๎
๎๎S_๎๎
๎๎๎๎_๎๎๎
๎๎๎๎๎๎B๎
๎๎๎_๎๎U
๎๎๎_๎๎๎
๎๎๎๎๎๎B๎
๎๎๎
๎๎๎๎๎๎๎๎๎
๎ ๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎S๎ ๎๎ ๎๎๎๎๎๎๎๎๎๎
๎๎ ๎
123
๎๎ ๎
123
๎๎ ๎
123
๎๎ ๎
123
1
1
1
1
B๎๎S๎S๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎
๎๎๎๎S๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎
๎_S๎ ๎๎
๎๎๎๎S๎๎๎๎๎๎๎S๎๎๎๎๎๎๎๎U๎๎๎
๎๎ ๎
1 2 3 4 5
๎ ๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎S๎๎๎๎๎๎3๎
B๎๎S๎S๎๎๎๎๎๎๎๎๎S๎๎๎
๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎U๎๎๎
๎๎ ๎_๎๎๎_๎๎ 3
F_USB3๎๎F๎๎๎๎๎๎๎๎๎๎๎
S๎ ๎๎ _๎๎๎๎๎๎๎
S๎ ๎๎ _๎๎๎๎๎๎๎
S๎ ๎๎ _๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎๎S๎๎๎F๎๎๎๎๎
๎๎๎
๎๎๎๎๎๎๎๎๎
๎๎B_๎
๎๎B_๎
๎๎๎๎๎๎๎F๎
๎๎_๎0๎
S๎๎๎๎๎๎๎
S๎๎๎๎
๎๎_๎0๎๎๎๎๎๎๎๎๎F๎๎๎๎๎๎๎๎
๎๎_๎๎F๎
๎๎๎_๎๎๎๎๎๎๎๎๎๎
๎_๎๎๎๎๎๎๎๎
๎๎_๎๎๎๎๎๎_B๎
๎๎๎
๎๎๎๎๎๎๎๎๎
U๎๎
S๎ ๎๎ _S๎๎
๎๎๎_๎๎๎๎๎๎๎๎
S๎๎๎F_๎๎๎๎๎๎๎๎๎
USB๎0_๎B
๎๎B_๎
F_USB3๎๎
๎๎๎
F_USB30๎3๎๎
๎๎๎๎
๎๎๎_๎๎๎
๎๎๎๎๎๎
๎๎_3๎๎๎๎๎๎๎๎๎๎๎๎๎๎U๎
S๎๎_๎๎๎
80 60110 42
6)๎ SATA3๎0/1/2/3/4/5๎(SATA๎6Gb/s๎Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel
ยฎ
๎Chipset๎supports๎RAID๎0,๎
RAID๎1,๎RAID๎5,๎and๎RAID๎10.๎Refer๎to๎Chapter๎3,๎"Con๎ฟguring๎a๎RAID๎Set,"๎for๎instructions๎on๎con๎ฟguring๎
a๎RAID๎array.
Pin๎No. De๎ฟnition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
To enable hot-plugging for the SATA ports, refer to Chapter 2,
"BIOS๎Setup,"๎"Settings\IO๎Ports\SATA๎And๎RST๎Con๎ฟguration,"๎
for more information.
SATA3
3 2
5 4
SATA3
77
11
1
1
7
7
1
0
- 15 -
To Next Page
Loading...
