- 24 -
10) M2A_CPU/M2Q_SB/M2P_SB (M.2 Socket 3 Connectors)
There are two types of M.2 SSDs: M.2 SATA SSDs and M.2 PCIe SSDs. This motherboard only supports
M.2 PCIe SSDs. Be sure to verify the type of M.2 SSDs you want to use. Please note that an M.2 PCIe
SSD cannot be used to create a RAID set with a SATA hard drive. Please navigate to the "Conguring a
RAID Set" page of GIGABYTE's website for instructions on conguring a RAID array.
* Types of M.2 SSDs supported by each M.2 connector:
M.2 PCIe x4 SSD M.2 PCIe x2 SSD M.2 SATA SSD
M2A_CPU
a a
r
M2Q_SB
a a
r
M2P_SB
a a
r
M2P_SB
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
B
USB0_B
B_
B_
F_USB3
F_USB303
_
_3U
S_
_S
SS_F
_
_
F
_SB
80110
M2A_CPU
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
B
USB0_B
B_
B_
F_USB3
F_USB303
_
_3U
S_
_S
SS_F
_
_
F
_SB
80
M2Q_SB
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
B
USB0_B
B_
B_
F_USB3
F_USB303
_
_3U
S_
_S
SS_F
_
_
F
_SB
80
& Please visit GIGABYTE's website for details on using M.2 EZ-Latch Plus.
Install the M.2 SSD: https://www.gigabyte.com/WebPage/920/M2-latchplus.html
Remove the M.2 SSD: https://www.gigabyte.com/WebPage/921/removeM2.html
* Motherboard heatsink design may vary by model.
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
M2A_CPU:
Step 1:
Use a screwdriver to unfasten the screws on the motherboard heatsink and then remove the motherboard
heatsink.
Step 2:
Insert the M.2 SSD into the M.2 connector at an angle. Press the M.2 SSD down and then use the included
screw to secure it in the connector.
Step 3:
Remove the protective lm from the thermal pad on the bottom of the heatsink. Then replace the heatsink
and secure it to the original hole.
M2Q_SB/M2P_SB:
Step 1:
Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the EZ-Latch
Plus clip to the desired mounting hole.
Step 2:
Insert the M.2 SSD into the M.2 connector at an angle. Press down on the front end of the M.2 SSD and
make sure the M.2 SSD is secured by the M.2 EZ-Latch Plus clip.
To Next Page
Loading...
