GNATUS Syncrus GL TB - User Manual

Questions and Answers

N
nicolemunozAug 16, 2025
What to do if there is no water from the syringe of my GNATUS Dental equipment?
- N
  Nathan SmithAug 16, 2025
  If there's no water coming from the syringe in your GNATUS dental equipment, there could be a couple of reasons. First, check if the water reservoir is empty and refill it with filtered water. Also, ensure that the compressor is plugged in, as a disconnected compressor can also cause this issue.
J
jordannicholasAug 19, 2025
Why is there no air coming from the syringe of my GNATUS Dental equipment?
- R
  Randy HannaAug 19, 2025
  If no air is coming from the syringe of your GNATUS dental equipment, the most likely cause is a disconnected compressor. Ensure the compressor is properly plugged in.
S
Scott HicksAug 22, 2025
How to increase the speed of a GNATUS Syncrus GL TB Dental equipment handpiece?
- M
  Mallory WeeksAug 22, 2025
  If your GNATUS dental equipment handpiece is running at a low speed, the inlet pressure might be below the specified level of 80 PSI / 5,52 BAR. Adjust the inlet pressure to 80 PSI / 5,52 BAR.
N
nicolebarkerAug 26, 2025
What to do if the Optilight LD (Syncrus GLF OPTI and GLC OPTI Delivery unit) of my GNATUS Dental equipment is not working?
- G
  gutierreztracyAug 26, 2025
  If your GNATUS Dental equipment Optilight LD (Syncrus GLF OPTI and GLC OPTI Delivery unit) isn't working, check the power supply to ensure there isn't a power cut. Also, verify if the chair's fuse has burned out and replace it if necessary.
N
Neil MercadoAug 28, 2025
Why doesn't disinfectant come from the handpiece terminals when operating the Bio-system on my GNATUS Syncrus GL TB Dental equipment?
- J
  Jessica ThompsonAug 28, 2025
  If no disinfectant is coming from the handpiece terminals when the bio-system is operated on your GNATUS dental equipment, several factors could be at play. First, ensure the bio-system reservoir is filled with disinfectant. Next, check if the chair fuse has blown and replace it if needed. Finally, confirm that the main or chair switch is turned on.
P
pearsonkathleenAug 31, 2025
What to do if the X-ray view on my GNATUS Syncrus GL TB does not work?
- D
  Dr. Ann Macias MDAug 31, 2025
  If the X-ray view is not working on your GNATUS dental equipment, it could be due to a burned chair fuse. Replace the chair's fuse. Also, check that the main or chair switch is turned on.
M
moneillSep 3, 2025
Why is there low pressure in the jet of my GNATUS Dental equipment?
- W
  Wendy WiseSep 3, 2025
  If there's low pressure in the jet of your GNATUS dental equipment, the compressor might be disconnected. Ensure the compressor is plugged in.
B
Billy GrahamSep 6, 2025
Why is there not enough bicarbonate in the jet of my GNATUS Syncrus GL TB?
- J
  Jessica BassSep 6, 2025
  If there is not enough bicarbonate in the jet of your GNATUS dental equipment (GLXF FULL, GLXC FULL, GLXF, GLXC, GLF JET and GLC JET Delivery Units), make sure that there is enough bicarbonate in reservoir (max. 40g). Also, the spout or reservoir outlet may be clogged, so you should clean clogged parts. If there is bicarbonate excess in reservoir, remove the excess. Finally, check if the jet position is correct and change position if needed.
T
Thomas ReyesSep 9, 2025
Why is there little water in the jet of my GNATUS Syncrus GL TB?
- L
  Lisa SmithSep 9, 2025
  If there's little water in the jet of your GNATUS dental equipment, first check if the water valve is closed and open it. Also, ensure the jet water reservoir is filled with water.
K
Kenneth DurhamSep 12, 2025
What to do if my GNATUS Syncrus GL TB Dental equipment is not polymerizing resins?
- A
  Alan AlvarezSep 12, 2025
  If your GNATUS dental equipment is not polymerizing resins, the resin might not be appropriate for the LED's photopolymerizer wave length range. Use the indicated resin for the photopolymerizer's wave length range, one that contains photoinitiators based on camphor-quinone.