Go Power! Electric GP-1750

Questions and Answers

L
lancereedAug 13, 2025
How to stop Go Power! Electric Inverter from causing TV interference?
- C
  Cathy WashingtonAug 13, 2025
  If your Go Power! Electric Inverter is causing television interference, ensure the chassis ground lug is firmly connected to your vehicle, boat, or home's ground system. Avoid operating high-power loads while watching TV. Verify your antenna provides a strong signal and uses quality cables. Position the TV as far as possible from the inverter. Keep battery cables short and twisted (2-3 twists per foot) to minimize interference.
K
karen51Aug 17, 2025
What to do if Go Power! Electric GP-1750 Inverter has low output voltage and red zone indicator?
- S
  shelley86Aug 17, 2025
  If your Go Power! Electric Inverter shows a low output voltage and the current indicator is in the red zone, it indicates an overload. To resolve this, turn off the inverter, reduce the load by disconnecting some devices, and then turn the inverter back on.
M
Michelle BrownAug 20, 2025
What to do if Go Power! Electric GP-1750 Inverter has no output voltage and voltage indicator in lower red zone?
- L
  Latasha FrancoAug 21, 2025
  If your Go Power! Electric Inverter isn't providing any output voltage and the voltage indicator is in the lower red zone, it's likely due to low DC input voltage. Recharge the battery and check all connections and cables to ensure they are properly connected.
D
davidnealAug 25, 2025
What to do if Go Power! Electric GP-1750 Inverter has no output voltage and no voltage indication?
- H
  Haley RamseyAug 25, 2025
  If your Go Power! Electric Inverter shows no output voltage and no voltage indication, first, ensure the inverter is switched on and check the wiring to the inverter. If that's not the issue, an internal fuse may have opened, or there might be reverse DC polarity. In these cases, have a qualified technician check and replace the fuse, ensuring correct polarity is observed.
P
parkercodyAug 28, 2025
Why is the low battery alarm always on for my Go Power! Electric Inverter?
- B
  Bryan BerryAug 28, 2025
  If your Go Power! Electric Inverter's low battery alarm is constantly on and the voltage indicator is below 11V, it could be due to poor DC wiring or a weak battery. Ensure you're using the correct cable and making solid connections. If the problem persists, consider replacing the battery.
E
elizabeth57Sep 1, 2025
What to do if Go Power! Electric GP-1750 Inverter has no output voltage and voltage indicator in upper red zone?
- K
  Kara TaylorSep 1, 2025
  If your Go Power! Electric Inverter shows no output voltage and the voltage indicator is in the upper red zone, it indicates high input voltage. Ensure the inverter is connected to a 12V battery and check the regulation of the charging system.
A
andrearichardsSep 4, 2025
Why is the AC output voltage low on my Go Power! Electric GP-1750 Inverter?
- J
  Jerry SchneiderSep 5, 2025
  If your Go Power! Electric Inverter is showing a low AC output voltage (95-105 VAC), it may be due to using a standard voltmeter. Use a true RMS averaging meter for accurate readings.
K
kwrightSep 9, 2025
How to eliminate buzz in audio systems with Go Power! Electric Inverter?
- E
  Eugene RandolphSep 9, 2025
  If you're experiencing a buzz in your audio systems when using a Go Power! Electric Inverter, it may be because the power supply in your audio device isn't adequately filtering the modified sine wave produced by the inverter. Try using a sound system with a higher quality power supply.

Summary

Inverter Specifications

GP-1750 Inverter Specifications

Detailed specifications for the GP-1750 Inverter, covering power, voltage, dimensions, and more.

GP-3000 Inverter Specifications

Inverter Installation Guide

Choosing an Installation Location

Connecting and Testing Procedures

DC Install Kits

Cable and Fuse Requirements

Grounding Instructions

Critical safety information and procedures for proper inverter grounding.

Operating the Go Power Inverter

Controls and Indicators

Power Output Considerations

Input Voltage and Protection

Troubleshooting Inverter Issues

Common Inverter Problems

Inverter Troubleshooting Guide

A detailed guide listing specific problems, their causes, and recommended solutions.

Inverter Troubleshooting Guide (Continued)

Go Power! Electric GP-1750 Specifications

General

Output Power	1750 W
Surge Power	3500 W
Input Voltage	12 VDC
Output Voltage	120 VAC
Output Waveform	Modified Sine Wave
Efficiency	90%
Weight	9.3 lbs (4.2 kg)
Dimensions	12.9 x 8.3 x 3.5 in (328 x 210 x 88 mm)
Output Frequency	60 Hz
Waveform	Modified Sine Wave
Cooling	Fan Cooled
Protection Features	Overload, Over Temperature