EasyManua.ls Logo

Graco 244811 - User Manual

Graco 244811
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
309368
Rev. H
First choice when
quality counts.t
INSTRUCTIONS
INSTRUCTIONS
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
Direct-Drive Pressure Washers
2730
Model 244811, Series B with Briggs & Stratton 6.5 HP Motor
2700 psi (186 bar, 18.6 MPa) Operating Pressure
3000 psi (210 bar, 21.0 MPa) Maximum Working Pressure
2730
Model 244812, Series B with Honda 6.5 HP Motor
2700 psi (186 bar, 18.6 MPa) Operating Pressure
3000 psi (210 bar, 21.0 MPa) Maximum Working Pressure
3030
Model 244813, Series B
3000 psi (210 bar, 21.0 MPa) Operating Pressure
3300 psi (227.5 bar, 22.75 MPa) Maximum Working Pressure
3340
Model 244814, Series B
3300 psi (227.5 bar , 22.75 MPa) Operating Pressure
3600 psi (248 bar, 24.8 MPa) Maximum Working Pressure
3540
Model 244815, Series B
3500 psi (241 bar, 24.1 MPa) Operating Pressure
3800 psi (262 bar, 26.2 MPa) Maximum Working Pressure
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441
ECOPYRIGHT 2001 GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
3300 Pressure Washer
Model 244814 Shown

Questions and Answers

  • D
    David HoffmanAug 10, 2025
    How to fix low pressure on Graco Pressure Washer?
    • J
      Jeremy MccoyAug 10, 2025
      To resolve low or fluctuating pressure in your Graco Pressure Washer, check the following: * Remove any kinks in the water inlet hose. * Replace the high pressure discharge hose if it's kinked. * Remove and clean or replace the water inlet screen if it's obstructed. * Tighten all water intake connections to eliminate air leaks. * Insert a high pressure nozzle. * Clean or replace the spray nozzle if it's obstructed or worn. * Inspect, clean, or replace the valve assembly on the pump if it's damaged or obstructed. * Replace worn pump packings. * Repair or replace the bypass valve if it's not operating correctly.
  • A
    Alicia FisherAug 15, 2025
    Why is water leaking from the heat dump valve on my Graco Pressure Washer?
    • R
      Russell HernandezAug 15, 2025
      If water is leaking from the “Heat Dump Valve” of your Graco Pressure Washer, it could be due to the water temperature being too high. To prevent this, avoid operating the unit in bypass mode (with the trigger gun closed) for more than 3 minutes. Alternatively, the valve itself may be defective and require replacement.
  • S
    Shawn TuckerAug 19, 2025
    How to fix detergent not siphoning in my Graco Pressure Washer?
    • B
      Brian TaylorAug 20, 2025
      If the detergent is not siphoning into the low pressure detergent mode on your Graco Pressure Washer, check these items: * Ensure the detergent strainer is fully submerged in the detergent solution. * Inspect, clean, or replace the detergent strainer if it's obstructed. * Inspect, clean, or replace the detergent hose if it's cut or obstructed. * Open the detergent adjusting knob on the pump (if applicable). Refer to “Cleaning with Detergents” pg.13. * Insert a 6540° (BLACK) nozzle, as it needs to be in low pressure mode. * Clean or replace the nozzle assembly if it's plugged. * Use one high pressure hose extension maximum. * Remove, clean or replace the Ball and Spring in Venturi if stuck.
  • D
    Dawn ThomasAug 25, 2025
    Why does the oil in my Graco Pressure Washer look milky?
    • K
      Kristin BakerAug 26, 2025
      If the oil in your Graco Pressure Washer appears milky or foamy, it indicates that there is water in the oil. To resolve this, change the pump oil and fill it to the proper level.
  • L
    lisapenningtonAug 30, 2025
    Why is water flowing back into the detergent container of my Graco Pressure Washer?
    • J
      Joshua JohnsonAug 30, 2025
      If water flows back into the detergent container of your Graco Pressure Washer, the ball and spring in the Venturi may be reversed, missing, or corroded. Remove, clean, or replace these components.
  • L
    Leslie BarrettSep 3, 2025
    What to do if water flows from the nozzle when the Graco Pressure Washer trigger gun is off?
    • M
      Marisa DuarteSep 4, 2025
      If water flows from the nozzle of your Graco Pressure Washer when the trigger gun is locked in the “OFF” position, it suggests that the gun is malfunctioning. You should repair or replace the gun.

Graco 244811 Specifications

General IconGeneral
Power SourceGasoline
Model244811
Pump TypeAxial Cam
Thermal Relief ValveYes
Soap ApplicatorYes
Hose Length25 ft
Engine190cc
CategoryPressure Washer
Wheel TypePneumatic
Engine Type4-stroke OHV

Related product manuals