Grandstream
GXP2130/2140/2160/2135/2170
IP Phone
Quick User Guide
Basic Phone Operation
For detailed information please
consult the GXP2130/2140/2160/2135/2170
User Manual
available at:
www.grandstream.com
©2014 Grandstream Networks, Inc. All rights
reserved.
Reproduction or transmittal of the entire or any
part, in any form or by any means, electronic or
print, for any purpose without the express
written permission of Grandstream Networks,
Inc. is not permitted. Information in this
document is subject to change without notice.
USING THE HEADSET OR SPEAKER
1) Use the Speaker Button to turn
speaker ON/OFF.
2) Use the Headset button to use
the headset once it had been connected.
MAKING A CALL
1) Take Handset/Headset off-hook or press
Speaker button or an available LINE key
(activates speakerphone) .
2) The line will have dial tone and the
corresponding line’s LED will turn green.
3) If you wish, select another LINE key
(alternative SIP account).
4) Enter the phone number.
5) Press the SEND button or press
the “DIAL” soft key.
REDIAL
1) Take the phone off-hook.
2) Press the SEND button or press
the “REDIAL” soft key.
Note: The phone will redial using the
same SIP account as was used for the last
call.
ANSWERING CALLS
Single Incoming Call:
1) Answer call by taking Handset/Headset
off hook or pressing SPEAKER or by
pressing the corresponding account LINE
button.
Multiple Incoming Calls:
1) When there is a call waiting, users will
hear a Call Waiting tone .
2) The next available line will flash red.
3) Answer the incoming call by pressing its
corresponding LINE button.
4) The current call will be put on hold.
5) Toggle between the calls using the LINE
button.
ENDING A CALL
End a call by pressing the “EndCall” soft key
or hang up the phone.
CALL HOLD/RESUME
1) Hold: Place a call on ‘hold’ by pressing
the hold button.
2) Resume: Resume call by pressing the
corresponding blinking LINE.
CALL TRANSFER
Assuming that you are in a call and wish to
transfer the call to another party.
Blind Transfer:
1) Press transfer button.
2) Dial the number and press the send button
to complete transfer of active call.
Attended Transfer:
1) Press an idle line key to make a new call and the
active LINE will be placed on hold automatically.
2) Once the call is established, press transfer
button followed by the LINE button of the held line to
transfer the call.
3) After the call is transferred, phone will display idle
screen.
Auto-Attended Transfer:
1) Set "Auto-Attended Transfer" to "Yes" on Web
GUI.
2) Establish one call first.
3) Press transfer key to bring up a new line,
and the first call will be placed on hold automatically.
4) Dial the number and press SEND button
to make a second call.
5) Press transfer key again to make the transfer.
Note: For Auto-Attended Transfer, after dialing out
the number for the second call, a “Split” soft key will
show. If the second call is not established yet
(ringing), pressing “Split” will hang up the second
call. If the second call is established (answered),
pressing “Split” will resume the second call and keep
the first call on hold.
3-WAY CONFERENCE
Initiate a Conference Call:
Assuming that you are already in a conversation and
wish to bring a third party together in a 3-way
conference.
1) Press conference button to bring
up conference dialing screen.
2) Dial the third party number followed by
SEND key.
3) When the call is established to the third
party, press the “ConfCall” soft key to initiate 3
-way conference.
Cancel a Conference Call:
1) Press “Cancel” soft key in conference
dialing screen to resume the two-way
conversation.
Hold The Conference:
1) Press hold button to hold the
conference call with all parties are on hold;
2) Press “ReConf” soft key to resume
conference call; or select the corresponding
blinking LINE to speak with an individual party.
End The Conference:
The conference will be terminated for all three
parties if the conference initiator hangs up or
presses “EndCall” soft key.
VOICEMAIL MESSAGE
A blinking red MWI (Message Waiting
Indicator) indicates a message is waiting.
1) Press the Message button to retrieve the
message. An IVR will prompt the user
through the process of message retrieval.
2) Press a specific LINE to retrieve messages
for a specific line account.
Note: Each account requires a voicemail
portal number to be configured in the
“voicemail user id” field.
MUTE/DELETE
1) Press the MUTE button to mute/
unmute the microphone.
2) The Mute icon indicates whether the
microphone is muted.
VOLUME ADJUSTMENTS
Use the volume button to
adjust the ring volume when the phone is idle.
Press the volume button during an active call
to adjust the call volume.
