Why is the wash tank filling time long in my GRANULDISK Washer?
If you are experiencing a long wash tank filling time, it means the level sensor in the wash tank hasn't been activated within 20 minutes of the rinse pump start. Check the water supply to the machine and the rinse pump. Clean the rinse nozzles and reset the alarm by pressing the STOP button. If the alarm continues, contact a service engineer.
What to do if the motor circuit breaker for the rinse pump tripped in GRANULDISK Washer?
If the motor circuit breaker for the rinse pump tripped, it means the motor is overloaded, likely because the impeller is blocked. In this case, you should contact a service engineer.
What to do if the overheating protector for wash tank tripped in GRANULDISK Washer?
If the overheating protector for the wash tank has tripped, it indicates that the wash tank heater has overheated. You should clean the level sensor in the wash tank and reset the overheat protection. If the error code reappears within a few hours, contact a service engineer.
What to do if the overheating protector for rinse tank tripped in GRANULDISK Washer?
If the overheating protector for the rinse tank has tripped, it indicates that the rinse tank heater has overheated. Clean the level sensor and reset the overheat protection. If the error code recurs within a few hours, call a service engineer.
What to do if the drain valve not closed in GRANULDISK Washer?
If the drain valve is not closed, it means that it has opened during an active process in the machine. Close the drain valve and reset the alarm by pressing the STOP button.
Why is the basket drive device blocked in my GRANULDISK Granule Gastro Dishwasher?
If your GRANULDISK Dishwasher basket drive is blocked, it means something is preventing the basket from rotating. Check for obstructions between the basket and the basket wheel. Afterward, reset the alarm by pressing the STOP button.
What to do if an initiation error of the temperature sensors has occurred in GRANULDISK Washer?
If an initiation error of the temperature sensors has occurred, it means the communication between the temperature sensors and the PCB was disturbed during start up or the temperature sensor in the wash tank or rinse tank is broken. Cut the power to the machine completely by switching the machine off at the wall socket. Wait 30 seconds. Switch the power back on. If the fault recurs, repeat the procedure once again. If the fault persists, contact a service engineer.
What to do if the drain valve is not closed in my GRANULDISK Granule Gastro?
If the drain valve of your GRANULDISK Dishwasher opens during operation, close it. Then, reset the alarm by pressing the STOP button.
What to do if there is incorrect upwards movement of the hood in GRANULDISK Washer?
If the hood's upward movement is incorrect, it means the hood hasn't reached the top within 20 seconds. Check the incoming water, reset the alarm by pressing the STOP button, and if the alarm continues, contact service personnel.
What to do if water level too low in rinse tank of GRANULDISK Washer?
If the water level is too low in the rinse tank, it indicates that the level has fallen incorrectly. Contact a service engineer.
Introduction for users, purpose of the manual and machine.
Essential safety guidelines, warnings, and precautions for operation.
Detailed specifications including dimensions, power, water, and programs.
Information on cleaning granules, their use, and disposal.
Guide to using QR codes for quick access to machine information.
Step-by-step guide to prepare and start the pot washing machine.
Instructions on how to load various types of utensils and baskets.
Explanation of buttons and functions on the machine's control panel.
How to select and run wash programs, and stop the machine.
Steps to change the display language on the control panel.
Instructions for adjusting the machine's date and time settings.
Procedure for collecting, cleaning, and managing wash granules.
Steps for cleaning the internal components and tank of the machine.
Procedures for securing the machine during extended periods of non-use.
Explanation of the GD Memo system for maintenance alerts.
Introduction to the GDTdirect™ tool for operating data and HACCP.
How to access and interpret wash program run data from the panel.
Viewing historical electricity and water usage figures.
Instructions for exporting wash data using a USB stick.
Common user-triggered alerts, their causes, and remedies.
Comprehensive list of machine error codes, meanings, causes, and solutions.
General| Brand | GRANULDISK |
|---|---|
| Model | Granule Gastro |
| Category | Dishwasher |
| Language | English |
To Next Page
