GRANULDISK Granule Combi User Manual

2
Declaration of Conformity
The Manufacturer:
GRANULDISK AB
Jägershillgatan 15
SE-213 75 MALMÖ, Sweden
declares that the following machinery:
The GRANULDISK system Granule Combi
®
Granule Combi is a unique Combi dishwasher which combines the award winning Granule Optimised
Washing Technology with the traditional dishwashing technique for plates, cutlery and most of the
crockery.
Basic conception
a) is manufactured in conformity with the Svenska Arbetarskyddsstyrelsens Författningssamling
AFS1994:48. This law conforms with the COUNCIL DIRECTIVE of 22 June 1998 concerning harmoni-
sation of member states legislation for machinery (the Machinery Directive 98/37/EG), with particu-
lar reference to Annex 1 concerning the essential health and safety requirements relating to the
design and construction of the machinery.
b) is besides the provisions under a) manufactured according to the following directives: the EC Low
Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC
c) is manufactured in conformity with the following harmonised standards: EN 60204-1:2006, EN
55014-1, EN 60335-2-58, EN 60439-1, EN 55022, EN ISO 13850:2008, EN ISO 13857:2008,
EN 61000-6-3 and EN 61000-6-2
d) is manufactured in accordance with EN 1717 and fitted with a type AB back flow protection device
with airgap in accordance with EN 13077:2008.
Malmö, Sweden 02.04.2009
Signed on behalf of GRANULDISK AB
GRANULDISK AB Jägershillgatan 15
213 75 MALMÖ
Phone: 040 671 50 60
Fax: 040 21 07 21
...............................................
Peter Schön
President
DRAFT

GRANULDISK Granule Combi Specifications

General

Brand	GRANULDISK
Model	Granule Combi
Category	Dishwasher
Language	English

Summary

User Guidance and Safety Information

Critical Safety Regulations and Warnings

Lists essential safety rules and precautions for operating the machine.

Technical Specifications and Machine Data

Installation and Initial Setup Procedures

Water Supply and Drainage System Connections

Instructions for connecting hot/cold water and the drain pipe.

Electrical and Ancillary System Connections

Detergent and Rinse Aid System Setup

Troubleshooting Common Machine Faults

Fault Identification and Check Procedures

Table outlining common faults and their corresponding checks.

Error Code Reference and Resolution Guide

Detailed Error Code Explanations and Remedies

Provides explanations and solutions for specific machine error codes.

Safe Power Disconnection for Maintenance Operations

Software Programming and Machine Control Functions

Flashloader Software: Installation, Connection, and Usage

Instructions for installing, connecting, and operating the Flashloader software.

Data Logging and HACCP Documentation System

Reading Machine Operating Data via Control Panel

1-Year Service Record and Inspection Checklist

2-Year Service Record and Inspection Checklist

Parts Adjustment and Exchange Procedures for GD Gastro/GC

Wash System Component Service and Replacement

Procedures for adjusting/exchanging drain valve sensor, pump, heater, and heat protector.

Hood and Safety System Adjustment and Alignment

Hood Alignment and Bracket Adjustment Procedures

Steps for aligning the hood and adjusting its support brackets.

Crush Protection System Adjustment and Testing

Guides on adjusting and testing the crush protection switch and springs.

Lift Yoke and Hood Component Service and Replacement

Lift Yoke Wheel Replacement Procedure

Sensor and Hydraulic Cylinder Service Procedures

Rinse System Component Maintenance and Replacement

Rinse Pump Exchange and System Checks

Rinse Pump Replacement Process

Guides on how to exchange the rinse pump and perform system checks.

Heating Element and Temperature Sensor Service

Rinse Tank Heating Element Replacement

Rinse Tank Temperature Sensor Exchange

1-Year Service Instructions and Procedures

Basket Drive Seal Replacement Procedure

2-Year Service Instructions and Procedures

Hood Seal Replacement Procedure