ENGLISH
8.6 Cycle of the machine
Between each change of polarity the box
displays "00" and the + and -
up for about 2 minutes.
After each reverse polarity time, the unit
indicates its maximum current during 2
minutes then ret
adjustment.
8.7
Verification and maintenance
Error signals:
If there is a problem with electric current, voltag
or internal temperature, the machine no longer
displays anything.
Only the indicator stays lit.
The machine will start up a
Adding salt:
Check the salt concentration. If the concentration
is less than 4g/l add salt, using the following
equation:
Q = (4 - T) x V
Q = quantity of Kg of salt to add
4 = correct salt concentration
T = concentration
V = pool volume in m3.
Always stop the chlorinator before adding any
product whatsoever. Wait until the salt has
dissolved before turning the chlorinator back on
again.
The salt concentration should be checked at
least twice a year.
Winterization:
If pool filtration is maintained during the winter
months, we recommend turning off the chlorinator
when the water temperature drops below 15°C,
removing the electrode from the chamber, and
replacing it with the cap that has been pro
this purpose.
Tips for proper use of the electrode:
The electrode is a wear-
sensitive part, and its life
span depends on the following factors:
- Salt concentration:
Never run the chlorinator with a salt concentration
less than 3.5 g/l.
- Wat
er temperature and winterization:
Turn off the machine whenever the water
temperature drops to 15°C or below.
- Adjustments:
Never leave the machine on maximum production
unless there is a chlorine shortage. An
101449 Installation and user
Between each change of polarity the box
After each reverse polarity time, the unit
indicates its maximum current during 2
Verification and maintenance
If there is a problem with electric current, voltage
or internal temperature, the machine no longer
Check the salt concentration. If the concentration
is less than 4g/l add salt, using the following
Always stop the chlorinator before adding any
product whatsoever. Wait until the salt has
dissolved before turning the chlorinator back on
The salt concentration should be checked at
If pool filtration is maintained during the winter
months, we recommend turning off the chlorinator
when the water temperature drops below 15°C,
removing the electrode from the chamber, and
replacing it with the cap that has been pro
vided for
Tips for proper use of the electrode:
sensitive part, and its life
span depends on the following factors:
Never run the chlorinator with a salt concentration
er temperature and winterization:
Turn off the machine whenever the water
temperature drops to 15°C or below.
Never leave the machine on maximum production
unless there is a chlorine shortage. An
"economical" setting would be about 75% of t
maximum current value printed on the side label.
- Reverse polarity:
Your machine is adjustable (see heading 7.5 ).
The electrode's life span depends on the number
of changes of polarity performed. For example, it
will wear out less quickly if change
occurs every 6 hours, and more rapidly if i
occurs every 2 hours.
Scale-covered or furred
The electrode should be clean
scaling.
If this should be the case, de
by dipping it in
a solution of 80% water and 20%
hydrochloric acid. Next, check the reasons for this
furring-up:
• the pH is too high
•
the salt concentration is too low
•
the setting for change of polarity is too long
•
the electrode is worn out
Compatibility:
The sterilizing a
gent (sodium hypochlorite)
pro
duced by the machine is compatible with most
pool water treatment products except for PHMB
polymers. In any case, when adding products, turn
off the chlorina
tor until the products are com
dissolved.
Washing the filter/
Turn the machine off when handling the filter
valve: washing, rinsing, draining, except if a flow
switch is installed.
Flow switch error:
In the case of a flow shortage, the machine
indicator will blink and display "99".
16
"economical" setting would be about 75% of t
he
maximum current value printed on the side label.
Your machine is adjustable (see heading 7.5 ).
The electrode's life span depends on the number
of changes of polarity performed. For example, it
will wear out less quickly if change
of polarity
occurs every 6 hours, and more rapidly if it
up electrode:
The electrode should be clean
-looking, without any
If this should be the case, de
-scale the electrode
a solution of 80% water and 20%
hydrochloric acid. Next, check the reasons for this
the salt concentration is too low
the setting for change of polarity is too long
the electrode is worn out
gent (sodium hypochlorite)
duced by the machine is compatible with most
pool water treatment products except for PHMB
polymers. In any case, when adding products, turn
tor until the products are com
pletely
Turn the machine off when handling the filter
valve: washing, rinsing, draining, except if a flow
In the case of a flow shortage, the machine
indicator will blink and display "99".
To Next Page
Loading...
