Gree GWH09QB-K3DNA6G - Page 32

29
Technical Information
Service Manual
● Under swing left and right mode, when the status is switched from off to , if press this button again 2s later, status will switch to off
status directly; if press this button again within 2s, the change of swing status will also depend on the circulation sequence stated above.
7.
button
8. SLEEP button
9. I FEEL button
11. CLOCK button
10. TIMER ON / TIMER OFF button
Press this button can select up & down swing angle. Fan blow angle can be selected circularly as below:
Under COOL, HEAT or DRY mode, press this button to start up sleep function. "
" icon is displayed on remote controller. Press this button
again to cancel sleep function and "
" icon will disappear.After powered on,Sleep Off is defaulted. After the unit is turned off, the Sleep
function is canceled. In this mode, the time of time can be adjusted. Under Fan and Auto modes, this function is not available.
Press this button to start I FEEL function and "
" will be displayed on the remote controller. After this function is set, the remote controller
will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the
detected temperature. Press this button again to close I FEEL function and "
" will disappear.
● Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high temperature
or low temperature in order to avoid detecting inaccurate ambient temperature.
Press this button to set clock time. "
" icon on remote controller will blink. Press " ▲ " or "
▲
" button within 5s to set clock time. Each
pressing of " ▲ " or "
▲
" button, clock time will increase or decrease 1 minute. If hold " ▲ " or "
▲
" button, 2s later, time will change quickly.
Release this button when reaching your required time. Press "CLOCK" button to conrm the time. "
" icon stops blinking.
Note:
● Clock time adopts 24-hour mode.
● The interval between two operation can’t exceeds 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER
OFF is the same.
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, "
" icon disappears and the word "ON" on remote controller
blinks. Press " ▲ " or "
▲
"button to adjust TIMER ON setting. After each pressing " ▲ " or "
▲
" button, TIMER ON setting will increase
or decrease 1min. Hold " ▲ " or "
▲
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER ON" to
conrm it. The word "ON" will stop blinking. "
" icon resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started
up, press "TIMER ON" button to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button,"
"icon disappears and the word "OFF" on remote controller
blinks. Press " ▲ " or "
▲
" button to adjust TIMER OFF setting. After each pressing " ▲ " or "
▲
" button, TIMER OFF setting will increase
or decrease 1min. Hold " ▲ " or "
▲
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER OFF"
word "OFF" will stop blinking. "
" icon resumes displaying. Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
"TIMER OFF" button to cancel it.
Note:
● Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the clock time.
● After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off
according to setting time. ON/OFF button has no effect on setting. If you don’t need this function, please use remote controller to cancel it.
● When selecting "
", air conditioner is blowing fan automatically. Horizontal louver will automatically swing up & down at maximum angle.
● When selecting "
、 、 、 、
", air conditioner is blowing fan at xed position. Horizontal louver will stop at the xed position.
● When selecting "
、 、
" , air conditioner is blowing fan at xed angle. Horizontal louver will send air at the xed angle.
● Hold " "button above 2s to set your required swing angle. When reaching your required angle, release the button.
Note:
● "
、 、
" may not be available. When air conditioner receives this signal, the air conditioner will blow fan automatically.
● Press this button continuously more than 2s, the main unit will swing back and forth from up to down, and then loosen the button, the unit
will stop swinging and present position of guide louver will be kept immediately.
● Under swing up and down mode, when the status is switched from off to
, if press this button again 2s later, status will switch to off
status directly; if press this button again within 2s,the change of swing status will also depend on the circulation sequence stated above.
no display
(horizontal louvers stops
at current position)