50
Technical Information
Service Manual
4. Combination of "TEMP" and "CLOCK" buttons: About
Energy-saving Function
Press "TEMP" and "CLOCK" simultaneously in COOL mode to
start energy-saving function. Nixie tube on the remote controller
displays "SE". Repeat the operation to quit the function.
5. Combination of "TEMP" and "CLOCK" buttons: About 8°C
Heating Function
Press "TEMP" and "CLOCK" simultaneously in HEAT mode to
start 8°C Heating Function Nixie tube on the remote controller
displays " " and a selected temperature of " 8°C ".
(46°F if Fahrenheit is adopted). Repeat the operation to quit the
function.
6. About Quiet function
When quiet function is selected:
(1) Under cool mode: Indoor fan operates at notch 4 speed.
10 minutes later or when indoor ambient temperature ≤
28°C, indoor fan will operate at notch 2 speed or quiet
mode according to the comparison between indoor ambinet
temperature and set temperature.
(2) Under heat mode: Indoor fan operates at notch 3 speed or
quiet mode according to the comparison between indoor
ambient temperature and set temperature.
(3) Under dry, fan mode: Indoor fan operates at quiet mode.
(4) Under auto mode: The indoor fan operates at the auto quiet
mode according to actual cool, heat or fan mode.
7. About turbo function
If start this function, the unit will run at super-high fan speed to
cool or heat quickly so that the ambient temp. approachs the
preset temp. as soon as possible.
8. About Sleep function
Under the fan, dry and auto mode, the sleep function cannot be
set up, select and enter into any kind of sleep mode, the quiet
function will be attached and stared, different quiet status could
be optional and turned off.
Operation guide
1. General operation
(1) After powered on, press ON/OFF button, the unit will start to
run. (Note: When it is powered on, the guide louver of main
unit will close automatically.)
(2) Press MODE button, select desired running mode.
(3) Pressing + or - button, to set the desired temperature.
(4) Pressing FAN button, set fan speed, can select AUTO FAN,
LOW, MEDIUM-LOW, MEDIUM, MEDIUM-HIGH and HIGH.
(5) Pressing and button, to select the swing.
FAN
TURBO
MOOE
ON/OFF
SLEEPQUIETLIGHT WiFi
TEMP I FEEL
CLOCK
TIMER ON
TIMER OFF
5
4
3
2
1
2. Optional operation
(1) Press SLEEP button, to set sleep.
(2) Press TIMER ON and TIMER OFF button, can set the
scheduled timer on or timer off.
(3) Press LIGHT button, to control the on and off of the displaying
part of the unit (This function may be not available for some
units).
(4) Press TURBO button, can realize the ON and OFF of TURBO
function.
WiFi
FAN
TURBO
MOOE
ON/OFF
SLEEPQUIETLIGHT
TEMP I FEEL
CLOCK
TIMER ON
TIMER OFF
4
3 1
2
Replacement of batteries in remote controller
battery
Cover of battery box
remove
reinstall
1. Press the back side of remote controller marked
with " ", as shown in the fig, and then push out the cover of
battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and make sure the
position of "+" polar and "-" polar are correct.
3. Reinstall the cover of battery box.
NOTICE:
● During operation, point the remote control signal sender at the
receiving window on indoor unit.
● The distance between signal sender and receiving window
should be no more than 8m, and there should be no obstacles
between them.
● Signal may be interfered easily in the room where there is
uorescent lamp or wireless telephone; remote controller should
be close to indoor unit during operation.
● Replace new batteries of the same model when replacement is
required.
● When you don't use remote controller for a long time, please
take out the batteries.
● If the display on remote controller is fuzzy or there's no display,
please replace batteries.
To Next Page
Loading...
