What to do if my Gree livo GEN 3 LIVV09HP230V1A system will not run?
If your Gree Air Conditioner isn't running, check if the circuit breaker has tripped or is turned off. Also, ensure the remote's power button is on and the batteries aren't low. The remote shouldn't be in sleep or timer mode. If these steps don't resolve the issue, it's best to contact a qualified service professional.
Why is my Gree livo GEN 3 LIVV09HP230V1A unit not heating or cooling adequately?
If your Gree Air Conditioner isn't heating or cooling well, first, make sure there are no obstructions blocking airflow into the room. Then, clean the air filter if it's dirty or blocked, as this can restrict airflow. Seal any gaps around doors or windows to prevent air from entering the room, and move any heat sources away from the area.
What to do if water is leaking from my Gree livo GEN 3 LIVV09HP230V1A indoor unit into the room?
If water is leaking from your Gree Air Conditioner's indoor unit into the room, ensure the unit is level from right to left. If it's not, level it. Also, check the condensate drain pipe for any restrictions or blockages and remove them to allow proper drainage. If the issue continues, contact a qualified service professional.
Why doesn't my Gree Air Conditioner wireless remote controller work?
If the wireless remote controller for your Gree Air Conditioner isn't working, start by checking and changing the batteries. Ensure the remote is within 25 feet (7.5 meters) of the indoor unit without any obstructions. If a replacement is needed, contact a qualified service professional. You can use the Aux Button on the unit to operate it in the meantime.
Why will my Gree livo GEN 3 LIVV09HP230V1A Air Conditioner unit not deliver air?
If your Gree Air Conditioner isn't delivering air, consider these points: In heating mode, the fan might not start for three minutes if the room is very cold, to prevent blowing cold air. In heat mode, the system may defrost for up to 10 minutes before heating if the outdoor temperature is low and humidity is high. In dry mode, the fan may stop for up to three minutes during the compressor off delay. If none of these apply, contact a qualified service professional.
How to stop my Gree livo GEN 3 LIVV09HP230V1A indoor unit from emitting unpleasant odor?
If your Gree Air Conditioner's indoor unit emits an unpleasant odor when started, it's likely due to mold or mildew on the coil surfaces or air filter. Wash the indoor air filter in warm water with a mild cleaner. If the odor persists, contact a qualified service professional to clean the coil surfaces.
Why does my Gree Air Conditioner system not restart?
If your Gree Air Conditioner system does not restart, it might be due to a built-in three-minute delay. This delay prevents the compressor from short cycling. Wait three minutes to allow the protection delay to expire.
What to do if I see water leaking from the outdoor unit of my Gree livo GEN 3 LIVV09HP230V1A Air Conditioner?
If you notice water leakage from the outdoor unit of your Gree Air Conditioner, it's likely normal. The outdoor unit generates condensate water during reverse cycle heating and defrost mode, so no action is needed.
Why do I hear a 'water flowing' sound from my Gree livo GEN 3 LIVV09HP230V1A?
If you hear a 'water flowing' or 'gurgling' sound from your Gree Air Conditioner, it is normal. These sounds occur due to refrigerant pressures equalizing when the compressor starts and stops. The noises should stop as the refrigerant system equalizes after two or three minutes.
Why do I hear a slight cracking sound when my Gree livo GEN 3 LIVV09HP230V1A stops or starts?
If you hear a slight cracking sound when your Gree Air Conditioner starts or stops, it's normal. This sound comes from parts expanding and contracting. The noise will stop as the temperature equalizes after 2 or 3 minutes.
General| Cooling Capacity | 9, 000 BTU/h |
|---|---|
| Heating Capacity | 9, 500 BTU/h |
| Energy Efficiency Ratio (Cooling) | 13.0 |
| Refrigerant | R410A |
| SEER | 16 |
| HSPF | 9 |
| Power Supply | 230V, 1Ph, 60Hz |
| Noise Level (Outdoor) | 50 dB(A) |
Highlights the aesthetic design, G10 Inverter technology, and air flow control features.
Explains the model naming convention and the meaning of each part of the model number.
Explains safety symbols (DANGER, WARNING, CAUTION, NOTE) and their meanings.
Details specific safety warnings related to children, installation, and maintenance.
Provides cautions regarding handling the unit, cleaning, and flammable substances.
Shows icons for COOL, DRY, HEAT, POWER, SET TEMP and describes the LED display.
Labels components of the indoor unit (Front Panel, Aux. Button, Air Filter, Horizontal Louver).
Labels components of the outdoor unit (Inter-Connection Wire, Drain Hose, Refrigerant Lines).
Describes the quiet operation of the units.
Explains the availability of four fan speeds.
Describes the feature that prevents cold air during heating startup.
Explains the mode that senses room temperature via the remote.
Details the bi-directional airflow control with vertical swing louvers.
Explains the mode for rapid cooling or heating.
Describes the function to prevent freezing in rooms.
Explains the programmable on/off timer function.
Lists the five operating modes: HEAT, COOL, DRY, FAN ONLY, AUTO.
Explains the function that adjusts temperature for comfort during sleep.
Describes the mode that optimizes compressor and fan speeds for energy saving.
Details the built-in diagnostics for error detection.
Explains how settings are retained during power interruptions.
Describes the function to prevent frost buildup in heating mode.
Highlights the reusable air filter's benefits.
Explains the temperature display unit selection (Fahrenheit/Celsius).
Describes the feature to prevent unauthorized setting changes.
Mentions AHRI listing and ETL certification.
Labels the buttons on the remote controller.
Explains various icons shown on the remote display.
Explains how to turn the unit on and off using the remote.
Describes how to select operating modes like AUTO, COOL, DRY, FAN, HEAT.
Details how to adjust fan speed and activate the X-FAN function.
Explains how to adjust the horizontal and vertical airflow direction.
Explains how to activate quick cooling or heating.
Describes how to adjust temperature settings using ▲ and ▼.
Explains how to activate the sleep mode.
Describes how to view different temperature displays (indoor/outdoor/set).
Explains how to turn the WiFi function on or off.
Describes how to control the indoor unit's display light.
Explains how to set the clock time on the remote.
Details how to set the timer functions for turning the unit on or off.
Explains how to activate energy saving mode using combination buttons.
Describes how to turn on/off the internal clean function.
Explains how to activate the 8°C heating function.
Details how to activate/deactivate the child lock.
Explains how to switch between Celsius and Fahrenheit.
Describes how to activate the I FEEL mode.
Instructions for changing remote control batteries and general operational notes.
Explains how to operate the unit in AUTO mode using the Aux button.
Instructions for cleaning the front panel of the indoor unit.
Steps for accessing, cleaning, and reinstalling the air filter.
Explains the three-minute delay before system restart.
Addresses odors caused by mold or mildew on coil surfaces or filters.
Explains normal sounds from refrigerant pressure equalization.
Explains fog/vapor appearance during cooling of humid air.
Explains normal sounds from parts contracting/expanding.
Lists common reasons for the unit not running.
Provides checks for inadequate heating or cooling performance.
Explains normal water generation during defrost and heating modes.
Addresses water leaks from the indoor unit and potential causes.
Lists reasons for remote control malfunction and troubleshooting steps.
Explains system functions or conditions that might prevent air delivery.
Explains condensation on louvers during humid cooling conditions.
Lists critical operational issues requiring immediate service.
Suggests using Sleep Mode for nighttime energy savings.
Advises on using curtains and shades to manage solar heat.
Recommends confining heating/cooling to specific rooms by closing doors.
Suggests regular maintenance like cleaning outdoor unit coils.
Advises removing furniture that obstructs airflow.
Recommends optimal temperature settings (e.g., 75°F) for efficiency.
Notes that lights generate heat, increasing AC load.
Suggests using Auto mode when the home is unoccupied.
Advises using lower fan speeds for energy savings.
Instructions for contacting for warranty service and product registration.
Fields for model, serial number, owner, and installation details.
Details limitations on implied and express warranties.
Lists items and conditions not covered by the warranty.
To Next Page