15
Technical Information
Service Manual
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user
status, but do not change the temperature, press "Turbo" button directly for confirmation.
individuation sleep setting
Note: In theabove presetting or enquiryprocedure, if continuously within10s, thereisnobuttonpressed,the sleep
there is no button pressed, the sleep curve setting status will be automatically quit andresumetodisplay theoriginal displaying.
curve setting within10s,
In thepresettingorenquiry procedure, press"ON/OFF" button, "Mode" button,"Timer"button or "Sleep" button, thesleep
curvesetting or enquirystatuswillquitsimilarly.
Pressthis button, couldselect displaying theindoor settingtemperature or indoorambient temperature.When theindoor unit firstly
poweronit will displaythe setting temperature,if thetemperature's displaying status is changedfromother status to" ",displays the
ambient temperature, 5s later or within 5s, it receives other remote control signal that will return to display the setting temperature.
if the users haven't set up the temperature displaying status,that will display the setting temperature.
10
TEMP:
CLOCK :
Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply press this button again.
After press of this button, disappears and "ON "blinks .0
0:00 is displayed for ON time setting.Within
12
13
Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply press the button again.TIMER OFF setting
Press CLOCK button, blinking . Within 5 seconds,pressing + or - button adjusts the present time.
Holding down either button above 2 seconds increases or decreases the time by 1 minute every 0.5
every 0.5 second. During blinking after setting, press CLOCK button
second and then by 10 minutes
again to confirm the setting,and then
QUIET:
11
Pressthis button, theQuietstatusis underthe Auto Quietmode(displayand "Auto"
""
signal)
and Quiet mode (display " "
singal) and Quiet OFF (there is no signal of " " displayed), after powered on, the Quiet OFF is defaulted.
Note: the Quiet function cannot be set up in Fan and Dry mode;Under the Quiet mode (Display " "signal),
not available.
thefan speedis
will be constantly
displayed.
T-ON / T-OFF:
+ or - butt on to adjust the time value.Every press of either
5 seconds,press
button changes the time
rapidly changes the time setting by 1 minute and then
setting by 1minute. Holding down either button
10 minutes.Within 5 Seconds after setting,press TIMER ON button to confirm.
is the same as TIMER ON.
● This function is only available for some models.
" " eht ,no denrut si noitcnuf iFiW nehW .noitcnuf iFiW ffo nrut ro no nrut ot nottub " iFiW " sserP
WiFi
icon will be displayed on remote controller; Under status of unit off, press "MODE" and " " buttons simultaneously for 1s, WiFi
module will restore to factory default setting.
WiFi
LIGHT:
15
Press LIGHT button to turn on the display's light and press this button again to turn off the display 's light. If the light is turned on
is displayed. If the light is turned off, disappears.
TURBO:
14
WiFi:
16
Press this button to activate / deactivate the Turbo function which enables the unit to reach the preset temperature in the shortest time.
In COOL mode,the unitwill blowstrong
Press "+
" and "- " buttons simultaneously
to lock or unlock the keypad. If the remote controller is
In this case,
pressing any button, blinks three times.
Combination of "+" and "-" buttons: About lock
17
cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating air at super
high fan speed.
locked, is displayed.
At unit OFF, press "MODE "
and " - " buttons simultaneously to switch between and .
ć
Combination of "MODE" and "-" buttons :
18
About switch between Fahrenheit and centigrade
Press
"
TEMP
"
and
"
CLOCK
"
simultaneously in COOL mode to start energy-saving function.
Nixie tube on the remote controller displays
"
SE
"
. Repeat the operation to quit the function.
Combination of " TEMP " and "CLOCK" buttons : About
Energy-saving Function19
To Next Page
Loading...
Need help?
General
