Green Bike KT-LCD8H - User Manual

KT-LCD8H eBike Display User Manual
Dear customer, please read this manual before you use KT-LCD8HDisplay. The manual will guide you use
the instrument correctly to achieve a variety of vehicle control and vehicle status displays.
Functions
and
Display
Instruments using the structure form of instrument body portion and the operation buttons are
designed separately.
1
UP Button
10
Backlight and headlights
2
SW Button
11
℃
Environment temperature
3
DOWN Button
℉
Environment fahrenheit
4 MOTOR
W
Power display
12 Km/H
Riding speed(metric)
5
ASSIST
Pas level
13
AVS
Average speed
6Km/H push power assist
MXS
MAX speed
6 THROTT
LE
Run sign
14
DST
Trip distance
7
Battery capacity indicator
ODO
Total distance
8 VO
L
Battery voltage
15
TIM
Single trip time
9
The brake display
TTM
Total trip time
1. Operation
1.
ON/OFF
Hold button long to turn on the power, and hold long for a second time to turn off
the power. When the motor stops driving and when the e-bike is not used for a consecutive
5 minutes, it will automatically shut down and turn off the motor power supply.
2.
Display
1
Hold button to start up and enter display .
2.1 Turn on backlight and headlights
Hold long to turn on backlight and headlights (the
controller should have headlight drive output function); hold
long again to turn off the backlight and headlights.
2.2 Assist ratio gear (ASSIST) switch
Hold or shortly to switch 1-5 file gear. Gear 1 is for
the minimum power, gear 5 is for the highest power. Eachstartup
will automatically restore the gear shutdown last time (the user can
set randomly). Gear 0 is without booster function.
2.3 6Km/H assist promotion function
Hold and flashes, the vehicle drives at the speed not
more than 6Km /h. Release button, the function is invalid.
2.4
Display
and
delete
of
single
data
After power on for 5 seconds, hold and at the
same time, single trip riding time (TM) and single trip distance
(DST) flash, hold button shortly, the content of both is
cleared. If failed holding the button within 5 seconds, it will
automatically return the display interface after 5 seconds, original content is preserved.
3.
Display
2
Hold button shortly in display 1 to enter display 2.
In the riding mode after 5 seconds, display 2 automatically
returns to display 1, and the original motor power (MOTOR W)
display is replaced with motor operating temperature display
(MOTOR ℃) display (the internal motor should be equipped
with the temperature sensor and the output of temperature detection signal).
4.
Display
3
Hold button shortly in display 2 to enter display 3.
In the riding condition, five seconds later, a single maximum
speed (MXS) display automatically returns to the real riding
speed (Km/H).
5.
In
display
3,
hold
button
shortly
(SW),and
the
display
will
re-enter
display
1.
6.
Hold
button
to
turn
off
the
display
and
the
power
supply
of
controller.

Summary

Functions and Display

1. Operation

Covers the basic operations of the e-bike display, including power control and display modes.

1. ON;OFF

Instructions for turning the e-bike display and motor power supply on and off.

2. Display 1

Description of the primary display mode and its features.

2.1 Turn on backlight and headlights

How to activate the display's backlight and headlights for visibility.

2.2 Assist ratio gear (ASSIST) switch

2.3 6 Km;H assist promotion function

Details on how to activate the 6Km/H push power assist feature.

2.4 Display and delete of single data

Instructions for viewing and clearing trip time and distance data.

3. Display 2

4. Display 3

Description of the third display mode, showing maximum speed.

6. Hold button to turn off the display

Procedure for turning off the display and controller power.

7. Automatically prompt interface

General Project Setting

Guide to configuring general project settings like speed and wheel diameter.

1. Set maximum riding speed

Procedure for setting the maximum allowable riding speed.

2. Wheel diameter setting

Instructions for setting the correct wheel diameter for accurate readings.

2. Set the metric units

Guide to selecting units for speed, distance, and temperature.

5. Exit from routine project setting

Outline Drawings and Dimensions

Provides physical dimensions and wiring details of the display unit.

1.Dimensions of main instrument body

Diagram showing the physical dimensions of the main display unit.

2.Mounting dimensions of double brackets

Specifications for mounting brackets for the display.

3.Dimensions of button box

Shows the dimensions of the separate button control unit.

4.Wiring diagram

Illustrates the wiring connections for the display and controller.

Green Bike KT-LCD8H Specifications

General

Display Type	LCD
Model	KT-LCD8H
Voltage	24V/36V/48V
Handlebar Size	22.2mm
Power Assist Levels	5 Levels
Waterproof Rating	IP65
Backlight	Yes