GreenWorks Pro MO60L01 User Manual (English)

Other manuals for GreenWorks Pro MO60L01

Questions and Answers:

D
David HarperAug 17, 2025
Why my GreenWorks Pro MO60L01 won't start?
- C
  Cynthia StricklandAug 18, 2025
  If your GreenWorks Pro Lawn Mower doesn't start, several factors could be at play. First, ensure the battery is fully charged and correctly inserted into the mower until it clicks into place. Also, confirm that the safety key is completely installed. If these steps don't resolve the issue, grass may be jammed between the deck and blade; in this case, remove the battery and check for any obstructions under the deck. If problems persist, the switch may be defective, or the battery might need service or replacement; you can call the toll-free helpline at 1-855-345-3934 for assistance.
S
Stephanie RobertsonAug 20, 2025
What to do if my GreenWorks Pro MO60L01 doesn't start?
- M
  marc04Aug 20, 2025
  If your GreenWorks Pro Lawn Mower doesn't start, there are a few potential causes. First, the battery capacity might be low, so charge the battery pack. Second, the start handle could be defective, requiring replacement. Finally, the battery key might not be inserted, so ensure the battery key is properly in place.
S
Stacey ArcherAug 22, 2025
How to improve mulching with GreenWorks Pro MO60L01?
- J
  Jason NicholsAug 22, 2025
  If your GreenWorks Pro Lawn Mower isn't mulching properly, it could be due to wet grass clippings sticking to the underside of the deck. To resolve this, wait until the grass dries before mowing. Also, make sure that the mulching plug is properly installed.
M
Mary PowersAug 26, 2025
Why GreenWorks Pro MO60L01 Lawn Mower cuts the grass unevenly?
- A
  aaron31Aug 26, 2025
  If your GreenWorks Pro Lawn Mower cuts the grass unevenly, the lawn surface may be rough or uneven. Inspect the mowing area and clear any obstacles. Also, the cutting height may not be set correctly. Try moving the wheels to a higher setting.
H
Heather TurnerAug 28, 2025
How to fix uneven cuts with my GreenWorks Pro MO60L01?
- M
  Morgan BowenAug 28, 2025
  If your GreenWorks Pro Lawn Mower cuts grass unevenly, it might be because the lawn is rough, so examine the mowing area. It could also be that the blade height is not set correctly, in which case you should move the wheels to a higher position.
P
Pamela HolmesAug 30, 2025
How to adjust the handle position on a GreenWorks Pro MO60L01?
- R
  Rachel GreeneAug 30, 2025
  If the handle of your GreenWorks Pro Lawn Mower is not in position, it's likely that the bolts are not engaged correctly. Adjust the height of the handle and make sure that the bolts and nuts are aligned correctly.
C
Christopher ReevesSep 1, 2025
Why is my GreenWorks Pro Lawn Mower so noisy and vibrating?
- S
  Steven LuceroSep 1, 2025
  If your GreenWorks Pro Lawn Mower is excessively noisy and vibrates, stop the motor immediately and inspect for any visible damage. The motor shaft might be bent, or the blade could be unbalanced. Repair the blade before attempting to restart the mower. If the vibration continues after these steps, it's recommended to call the toll-free helpline at 1-855-345-3934 for further assistance.
S
Shane GrantSep 4, 2025
What to do if GreenWorks Pro MO60L01 is hard to push?
- J
  Jeffrey NortonSep 4, 2025
  If your GreenWorks Pro Lawn Mower is hard to push, it might be due to the grass being too tall or the cutting height being set too low. Try raising the cutting height to see if that makes a difference. Additionally, check the grass catcher bag; if the rear of the bag is dragging in thick grass, empty the grass clippings from the bag.
D
Donna RamseySep 6, 2025
Why does my GreenWorks Pro Lawn Mower stop during mowing?
- M
  misty45Sep 6, 2025
  Your GreenWorks Pro Lawn Mower might stop mowing for several reasons. The blade height could be too low, so try increasing it. The battery pack might be out of power, so ensure it is charged. Grass clippings might be attached to the deck or blade; in this case, remove the battery pack and check the deck. Also, the operating temperature of the machine might be too high, so allow the machine to cool.
S
Savannah BrownSep 9, 2025
Why is my GreenWorks Pro Lawn Mower hard to push?
- S
  Scott KlineSep 9, 2025
  If your GreenWorks Pro Lawn Mower is hard to push, it could be because the grass is too tall, or the blade height is too low, so try increasing the blade height. Alternatively, the grass catcher and blade might be dragging in thick grass, so empty the grass clippings from the grass catcher.

GreenWorks Pro MO60L01 Specifications

General

Motor	Brushless
Voltage	60 V
Deck Material	Steel
Self-Propelled	Yes
Mulching Capability	Yes
Bagging Capability	Yes
Side Discharge	Yes
Power Source	Battery
Battery Included	Yes
Charger Included	Yes
Cutting Width	21 inches
Battery	4.0Ah Lithium-Ion
Drive System	Rear Wheel Drive