Grundig Sonoclock 3000

To Next Page

18/39

Grundig Intermedia GmbH

Thomas-Edison-Platz 3

D-63263 Neu-Isenburg

CLOCK RADIO

Sonoclock 3000

www.grundig.com

DEEN

These additives can corrode the

device supports, leaving resi-

dues on the furniture surfaces

which can be difficult or impos-

sible to remove.

▪

Only use the device in a moder-

ate climate.

▪

Do not use any cleaning agent,

as this may damage the casing.

Clean the device with a clean,

moist leather cloth.

▪

Do not expose the back-up bat-

tery to extreme heat, caused for

example by direct sunlight, heat-

ers or fire.

▪

Never open the device casing.

No warranty claims are ac-

cepted for damage caused by

incorrect handling.

Compliance with RoHS Directive

The product you have purchased complies with EU

RoHS Directive (2011/65/EU). It does not contain

harmful and prohibited materials specified in the

Directive.

Package information

Packaging materials of the product are

manufactured from recyclable materials in

accordance with our National

Environment Regulations. Do not dispose

of the packaging materials together with the domes-

tic or other wastes. Take them to the packaging mate-

rial collection points designated by the local authori-

ties.

This device is noise-suppressed according to the

applicable EU directives. This product fulfils the

European directives 2014/53/EU, 2009/125/EC

and 2011/65/EU. You can find the CE declaration

of conformity for the device in the form of a pdf file

on the Grundig Homepage

www.grundig.com/downloads/doc

Power supply:

AC Adaptor Input:100 - 240V

, 50/60 Hz 0.25A

Output: 5V 1500mA

Max. Power consumption:

<11W (operation)

<1W (standby)

Output:

USB host: 5V 1A charge out

Back up micro batteries:

Back up DC Batt: 2 x 1.5v UM4/R03/AAA

Frequency bands:

FM 87.5 ...108.0 MHz

Circuit features:

Loudspeaker: 3 inch

Output Power: 2 W

Dimensions:

W x H x L 200 x 120 x 65 cm

Weight: 450 gr

Technical and design modifications reserved.

POWER SUPPLY

Mains operation

Check that the mains voltage on the type plate (on

the bottom of the device) corresponds to your local

mains supply. If this is not the case, contact your spe-

cialist dealer.

1 Plug the power adaptor into the socket

(100 - 240V

, 50/60 Hz).

Caution:

▪

The device is connected to the mains with the

power plug. To fully disconnect the device from

the mains, pull out the plug.

▪

The mains plug is used to disconnect the device. It

shall remain readily operable and should not be

obstructed during intended use.

Inserting the back-up battery

The back-up batteries ensure that the stored set¬tings

are not lost in the case of a power failure.

1 Open the battery compartment by pressing the

area market and pushing down the cover.

2 Observe the polarity marked on the base of the

battery compartment when inserting the batteries

(micro batteries, 2 x 1.5 V, R03/ UM 4/ AAA).

3 Close the battery compartment.

Note:

▪

Remove the back-up battery when it is flat or when

you know that the device will not be used for a

long period of time.

Environmental note:

▪

Batteries, including those which do not contain

heavy metal, should not be disposed of with

household waste. Always dispose of used batter-

ies in accordance with local environmental regu-

lations.

RADIO MODE

Antenna

For the best FM (UHF) reception it is sufficient to align

the wire antenna accordingly.

Switching on and oﬀ

1 Switching the device from standby with

»ON/OFF« button.

2 Switch the device to standby with »ON/OFF«

button.

Searching for and saving radio sta-

tions - automatically

You can store 10 radio stations on presets.

1 Activate the station search by pressing

»TUNING+/HR« or »TUNING-/MIN« buttons

until the frequency display changes to rapid run-

through.

The search stops when a station is found.

Note:

▪

To move the frequency forward in steps, briefly

press »TUNING+/HR« or »TUNING-/MIN«

several times.

2 Press and hold the »PRESET« button to activate

the memory function.

3 Press »TUNING+/HR« or »TUNING-/MIN«

buttons to select the preset.

4 Press the »PRESET« button to save the station.

Note:

▪

If the stations are already stored on the presets,

they are overwritten when new stations are stored.

5 To store more stations, repeat the steps 1 to 4.

Selecting stored stations

1 Select the preset by pressing the »PRESET« button

to select the preset stations one after another.

Adjusting the volume

1 Adjust the volume with »VOLUME -/AL 1« or

»VOLUME +/AL 2« buttons.

Setting the brightness of the display

1 Press the »SLEEP/SNOOZE/DIMMER« button

to adjust brightness levels in high, middle and low

levels.

TIMER MODE

Setting the time

1 Switching the device to standby with

»ON/OFF« button.

2 Press and hold the »TIME/MODE« button for

two seconds to activate the setting. The current

day of the week will be flashing on the LCD. »d1«

is Monday, and »d7« is Sunday.

3 Then press the »TIME/MODE« button again for

setting the current time.

4 Press »TUNING-/MIN« to set the minutes;

5 Press »TUNING+/HR« to set the hours;

6 Press the »TIME/MODE« button again to con-

firm the settings.

Setting the alarm time

1 Switch the device to standby with »ON/OFF« but-

ton;

2 Press and hold the »VOLUME -/AL 1« button

for alarm 1 or »VOLUME +/AL 2« for alarm 2;

3 For example, press and hold

»VOLUME -/AL 1« button to Then the alarm

days will be flashing on the LCD.

Activating and deactivating the alarm

1 In standby mode, press »VOLUME -/AL 1« or

»VOLUME +/AL 2« button to activate the alarm

with last used alarm settings.

2 For example, if pressed »VOLUME -/AL 1« but-

ton, the last used alarm time would be displayed;

3 By repeatedly pressing the »VOLUME -/AL 1«

button, the radio will display last set alarm time,

the » « and the » « icons.

Sleep timer

1 Press and hold the

»SLEEP/SNOOZE/DIMMER« button for about

2 seconds to activate the sleep timer.

2 Then repeatedly press the

»SLEEP/SNOOZE/DIMMER« button to select

the auto switch-off timer from 90 minutes to 10

minutes.

3 To switch off the sleep timer before the set time

press and hold »SLEEP/SNOOZE/DIMMER«

button for about 2 seconds, then repeatedly press

the button again until »OFF« is displayed.

4 Press the »TUNING-/MIN« or »TUNING+/

HR« buttons to adjust the alarm days.

5 Press the »VOLUME -/AL 1« button to confirm;

6 Press the »TUNING-/MIN« button to set the

alarm minutes;

7 Press the »TUNING+/HR« button to set the

alarm hours;

8 Press the »VOLUME -/AL 1« button to finish the

alarm 1 settings.

Note:

▪

The device wakes you up at the set alarm time, the

alarm duration is 60 minutes.

Interrupting the alarm

▪

Press the »SLEEP/SNOOZE/DIMMER« while

the alarm is sounding.

Note:

▪

The alarm signal will be stopped, and the alarm

will be sounded again after nine minutes.

Cancelling the alarm

1 Press »ON/OFF« while the alarm is sounding.

Note:

▪

The alarm will be sounded again at the next set

alarm time.

SETUP AND SAFETY EN

▪

This device is designed for the

playback of audio signals. Any

other use is expressly prohibited.

▪

Protect the device from moisture

(water drops or splashes). Do

not place any vessels such as

vases on the device. These may

be knocked over and spill fluid

on the electrical components,

thus presenting a safety risk.

▪

Do not place any naked flames

such as candles on the device.

▪

Thunderstorms are a danger to

all electrical devices. Even if the

device is switched off, it can be

damaged by a lightning strike to

the mains cable.

Charging a mobile phone

The USB socket on the back side can provide DC

power of 5V for charging a mobile phone. Connect

the mobile phone to the USB socket with an appro-

priate cable. The USB power is available in all the

operating modes and including standby mode. Refer

to the user manual or the manufacturer of the mobile

phone to verify if it supports charging from an USB

power. The USB socket is suitable for DC power-out

only and cannot be used for e.g. playback of music

from a USB stick.

▪

The type plate is located on the

bottom of the device.

▪

Do not expose the device to ex-

treme heat, caused for example

by direct sunlight, heator fire.

Compliance with the WEEE Directive

and Disposing of the Waste Product:

This product complies with EU WEEE Directive

(2012/19/EU). This product bears a classification

symbol for waste electrical and electronic equipment

(WEEE).

This product has been manufactured with

high quality parts and materials which

can be reused and are suitable for recy-

cling. Do not dispose of the waste product

with normal domestic and other wastes at

the end of its service life. Take it to the collection

center for the recycling of electrical and electronic

equipment. Please consult your local authorities to

learn about these collection centers.

TIME

TUNING+/HR VOL+/AL 2

VOL-/AL 1

TUNING-/MIN

ON/OFF

PRESET

USB

Always disconnect the mains

cable during a storm.

▪

If malfunctions occur due to

static electricity charges or brief

mains voltage surges, reset the

device. To do this, pull out the

mains adapter and connect it

again after a few seconds.

▪

Make sure the device is ade-

quately ventilated. Do not cover

the ventilation slots with newspa-

pers, table cloths, curtains, etc.

▪

When deciding where to place

the device, please note that furni-

ture surfaces are covered by var-

ious types of varnish and plastic,

most of which contain chemical

additives.

SLEEP

SNOOZE

DIMMER

Need help?

Do you have a question about the Grundig Sonoclock 3000 and is the answer not in the manual?

This document describes the Grundig Sonoclock 3000, a clock radio designed for the playback of audio signals. Any other use is expressly prohibited.

Function Description

The Sonoclock 3000 serves as a clock radio with FM radio capabilities and alarm functions. It allows users to set alarms, listen to radio stations, and charge mobile phones via a USB port. The device is equipped with a display that shows the time, alarm settings, and radio frequency.

Radio Mode: The device features an FM radio with a frequency range of 87.5 to 108.0 MHz. For optimal reception, the wire antenna should be aligned accordingly. Users can switch the device on and off from standby mode using the "ON/OFF" button. The device supports automatic searching and saving of up to 10 radio stations on presets. To activate the station search, users press and hold the "TUNING+/HR" or "TUNING-/MIN" buttons until the frequency display shows rapid run-through. The search stops when a station is found. To move the frequency forward in steps, users briefly press the "TUNING+/HR" or "TUNING-/MIN" buttons. Once a station is found, it can be saved to a preset by pressing and holding the "PRESET" button, selecting the desired preset with "TUNING+/HR" or "TUNING-/MIN" buttons, and then pressing "PRESET" again to save. If stations are already stored on presets, they will be overwritten when new stations are saved. Stored stations can be selected sequentially by pressing the "PRESET" button.

Timer Mode: The device allows users to set the time and alarm times.

Setting the Time: From standby mode, press and hold the "TIME/MODE" button for two seconds. The current day of the week will flash on the LCD. Press "TIME/MODE" again to set the current time. Use "TUNING-/MIN" to set minutes and "TUNING+/HR" to set hours. Press "TIME/MODE" again to confirm the settings.
Setting the Alarm Time: The device supports two alarms (Alarm 1 and Alarm 2). From standby mode, press and hold "VOLUME -/AL 1" for Alarm 1 or "VOLUME +/AL 2" for Alarm 2. The alarm days will flash on the LCD. Use "TUNING-/MIN" or "TUNING+/HR" buttons to adjust the alarm days. Confirm with "VOLUME -/AL 1". Then, set the alarm minutes with "TUNING-/MIN" and hours with "TUNING+/HR". Press "VOLUME -/AL 1" to finish the alarm settings. The device wakes users up at the set alarm time, and the alarm duration is 60 minutes.
Interrupting the Alarm: While the alarm is sounding, press "SLEEP/SNOOZE/DIMMER". The alarm signal will stop and sound again after nine minutes.
Cancelling the Alarm: While the alarm is sounding, press "ON/OFF". The alarm will sound again at the next set alarm time.
Activating and Deactivating the Alarm: In standby mode, press "VOLUME -/AL 1" or "VOLUME +/AL 2" to activate the alarm with the last used settings. Repeatedly pressing these buttons will display the last set alarm time and the alarm icons.
Sleep Timer: To activate the sleep timer, press and hold the "SLEEP/SNOOZE/DIMMER" button for about 2 seconds. Repeatedly pressing this button allows selection of an auto switch-off timer from 90 minutes down to 10 minutes. To switch off the sleep timer before the set time, press and hold "SLEEP/SNOOZE/DIMMER" for about 2 seconds, then repeatedly press the button until "OFF" is displayed.

Volume and Display Brightness: The volume can be adjusted using the "VOLUME -/AL 1" or "VOLUME +/AL 2" buttons. The display brightness can be adjusted to high, middle, and low levels by pressing the "SLEEP/SNOOZE/DIMMER" button.

Mobile Phone Charging: The USB socket on the back of the device provides 5V DC power for charging mobile phones. Users connect their mobile phone to the USB socket with an appropriate cable. The USB power is available in all operating modes, including standby. The USB socket is suitable for DC power-out only and cannot be used for playback of music from a USB stick.

Important Technical Specifications

Power Supply:
- AC Adaptor Input: 100 - 240V~, 50/60 Hz 0.25A
- Output: 5V 1500mA
Max. Power Consumption:
- <11W (operation)
- <1W (standby)
Output:
- USB host: 5V 1A charge out
Back-up Micro Batteries:
- 2 x 1.5V UM4/R03/AAA
Frequency Bands:
- FM 87.5 ...108.0 MHz
Circuit Features:
- Loudspeaker: 3 inch
- Output Power: 2 W
Dimensions:
- W x H x L 200 x 120 x 65 cm
Weight: 450 gr

Technical and design modifications are reserved.

Usage Features

User-friendly Interface: Buttons for "TIME/MODE", "PRESET", "TUNING+/HR", "TUNING-/MIN", "VOL-/AL 1", "VOL+/AL 2", "ON/OFF", "SLEEP/SNOOZE/DIMMER", and "USB" are clearly labeled on the device.
Battery Backup: The device uses two 1.5V AAA micro batteries (UM4/R03) to ensure that stored settings are not lost during a power failure.
USB Charging Port: A convenient USB port on the back allows for charging mobile phones.
Display: The LCD display shows time, frequency, and alarm settings, with adjustable brightness.

Maintenance Features

Cleaning: Do not use any cleaning agent, as it may damage the casing. Clean the device with a clean, moist leather cloth.
Ventilation: Ensure the device is adequately ventilated. Do not cover ventilation slots with newspapers, tablecloths, curtains, etc.
Environmental Considerations:
- WEEE Directive (2012/19/EU): The product complies with EU WEEE Directive and bears a classification symbol for waste electrical and electronic equipment. It should not be disposed of with normal domestic waste but taken to a collection center for recycling.
- RoHS Directive (2011/65/EU): The product complies with EU RoHS Directive and does not contain harmful or prohibited materials.
- Packaging: Packaging materials are recyclable and should be disposed of at designated collection points.
- Batteries: Used batteries, including those not containing heavy metal, should not be disposed of with household waste. Dispose of them according to local environmental regulations. Remove backup batteries if they are flat or if the device will not be used for a long period.
Safety Precautions:
- Moisture Protection: Protect the device from moisture (water drops or splashes). Do not place vessels such as vases on the device, as spills can cause electrical hazards.
- Heat Protection: Do not expose the device or its backup battery to extreme heat from direct sunlight, heaters, or fire.
- Open Casing: Never open the device casing. Warranty claims will not be accepted for damage caused by incorrect handling.
- Thunderstorms: Disconnect the mains cable during a storm to protect the device from lightning strikes.
- Mains Connection: The device is connected to the mains with a power plug. To fully disconnect, pull out the plug. The mains plug should remain readily operable and unobstructed.
- Static Electricity/Voltage Surges: If malfunctions occur due to static electricity or brief mains voltage surges, reset the device by pulling out the mains adapter and reconnecting it after a few seconds.
- Placement: Be aware that furniture surfaces covered by certain varnishes and plastics may contain chemical additives that can corrode the device supports, leaving residues.
- Climate: Only use the device in a moderate climate.

The type plate is located on the bottom of the device. The CE declaration of conformity for the device can be found as a PDF file on the Grundig Homepage: www.grundig.com/downloads/doc.