To Next PageTo Next Page
Need help?Do you have a question about the Guardian Plus GSEH3K and is the answer not in the manual?
Explains symbols used for safety and caution, including potential for injury or unit damage.
Introduces the whole-house HEPA filtration and ventilation system and its benefits.
Instructions for inspecting the unit for shipping damage and checking contents.
Details weight, duct collar types, electrical supply, and power consumption for different models.
Illustrates physical dimensions and air distribution ports for various unit models.
Presents data on net ventilation airflow and gross air flow for specific models.
Provides clearance requirements for door opening and top access for servicing.
Map and guidelines to determine the appropriate heat or energy recovery unit based on location.
Chart to help select the installation method (Stand Alone, Central Draw Point, Return-to-Return).
Table providing recommended maximum lengths for various flexible duct types and airflow.
Introduces common installation types and unit mounting options.
Illustrates a central draw point installation for the GSFH1K model.
Shows standalone and return-to-return installation types for the GSFH1K.
Illustrates central draw point installation for specific models.
Shows standalone, return-to-return, and outdoor connections for multiple models.
Details standalone installation in basements and garage closets, including considerations.
Cautionary note regarding continuous operation to prevent condensation in freezing temperatures.
Details standalone installation in attics, including considerations and cautions.
Describes simplified installation using existing ductwork in a basement.
Explains return-to-return installation in crawl spaces and attics.
Notes on blower operation, duct insulation, and unit behavior in cold weather.
Lists necessary tools and materials and guides on mounting unit ports.
Details installation using isolator pads or hanging the unit via chains and springs.
Provides instructions for door removal, panel access, and securing suspension hooks.
Guides on installing 8-inch ducts and registers for standalone systems.
Instructions for installing stale air collection registers and ductwork.
Instructions for installing fresh/filtered air distribution registers and ductwork.
Connects 8" flexible ducts to unit connectors for standalone systems.
Details connecting stale and filtered air ductwork for central draw point systems.
Describes punching holes and connecting ducts for central draw point systems.
Guides for connecting filtered and stale air ductwork in return-to-return systems.
Attaches exhaust air duct to the correct port for return-to-return systems.
Connects insulated flexible ducts to the Tandem transition for specific models.
Instructions for assembling, locating, and warnings for the AirDuo exterior hood.
Details cutting holes and connecting the Tandem transition to the exterior backplate.
Attaches hood to backplate and describes optional Alpine/Pine filter.
Guides for assembling AirDuo and optional single fresh air inlet exterior hoods.
Specifies placement distances and warnings for locating multiple exterior hoods.
Connects insulated ducts to exterior hoods, ensuring proper sealing.
Attaches backplates and hoods, ensuring proper seal and alignment.
Instructions for cleaning and reinstalling the optional Alpine/Pine filter.
Guides on locating Breidert caps, considering airflow and cross-contamination.
Connects insulated ducts to Breidert caps, identifying ducts by color dots.
Connects flexible ducts to the 5" to 6" oval ports of the unit.
Repeats connection steps and provides a caution about insulation compression.
Step-by-step guide for connecting the drain fitting and creating a water trap.
Covers insulating cabinet, ductwork, sealing ports, and installing heating cables.
Provides dimensions and instructions for fabricating a 2" thick insulation blanket.
Details fabricating and sealing an insulated enclosure using duct board.
Explains the 3-position main switch (OFF, NORMAL/REMOTE, BOOST) functions.
Identifies the available wall controllers: ACCGSC1 and ACCGSC3.
Shows controller dimensions and mounting options (recess or surface).
Warns about electrical shock and details routing and connecting control cable wires.
Guides on reinstalling the controller cover and wiring to unit terminals.
Details power indicator, filter maintenance indicator, and reset hole.
Explains how to use the controller's OFF, Low, and High speed settings.
Describes indicators for fresh air, recirculation, ventilation speeds, and filter maintenance.
Explains operation for OFF, Low/High Ventilation, and Recirculation modes.
Lists equipment needed for balancing and preliminary setup steps.
Guides on installing flow collars and performing the air balancing procedure.
Instructions for preparing the unit and removing components for maintenance.
Guides on replacing the prefilter and reinstalling the filter cartridge.
Details cleaning procedures for heat and energy recovery cores.
Instructions on how to reset the filter maintenance indicator light.
Procedure for annual maintenance, including HEPA filter replacement.
Guides for master reset and cleaning the optional Alpine/Pine filter.
Lists common unit problems and their corresponding solutions.
Outlines the terms, conditions, and duration of the manufacturer's warranty.
General| Category | Fan |
|---|---|
| Oscillation | Yes |
| Number of speeds | 3 |
| Power | 50W |
| Voltage | 220-240V |
| Frequency | 50Hz |
| Color | White |
| Model | GSEH3K |
| Speed Settings | 3 |
| Material | Plastic |
