Guimbal Cabri G2 User Manual

www.guimbal.com
C
C
C
A
A
A
B
B
B
R
R
R
I
I
I
®
®
®
G
G
G
2
2
2
M
M
M
a
a
a
i
i
i
n
n
n
t
t
t
e
e
e
n
n
n
a
a
a
n
n
n
c
c
c
e
e
e
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
a
a
a
n
n
n
d
d
d
i
i
i
n
n
n
s
s
s
t
t
t
r
r
r
u
u
u
c
c
c
t
t
t
i
i
i
o
o
o
n
n
n
s
s
s
f
f
f
o
o
o
r
r
r
c
c
c
o
o
o
n
n
n
t
t
t
i
i
i
n
n
n
u
u
u
e
e
e
d
d
d
a
a
a
i
i
i
r
r
r
w
w
w
o
o
o
r
r
r
t
t
t
h
h
h
i
i
i
n
n
n
e
e
e
s
s
s
s
s
s
This manual includes the material required to be furnished to the operator
by EASA CS 27 and Part 21.
Note : It is the user’s responsibility to maintain manual currency.
A IX - EN -P ROVENCE , F RANCE

Guimbal Cabri G2 Specifications

General

Model	Cabri G2
Type	Light Helicopter
Engine	Lycoming O-360-J2A
Maximum Speed	185 km/h (115 mph, 100 kn)
Maximum Takeoff Weight	700 kg (1, 543 lb)
Rotor Diameter	7.2 m (23 ft 7 in)
Crew	1
Length	6.31 m (20 ft 8 in)
Main rotor area	40.7 m2 (438 sq ft)
Manufacturer	Hélicoptères Guimbal
Range	700 km (435 mi, 378 nmi)
Capacity	2
Never exceed speed	130 knots
Service ceiling	13, 000 ft
Power	145 hp
Cruise speed	90 knots

Summary

Section A General

A-1 Introduction

Provides overview of the manual and its structure.

A-2 Cabri G2 Description

Details the helicopter's basic characteristics and optional equipment.

A-3 Helicopter Basic Servicing

Covers essential servicing tasks like ground handling and lubrication.

Section B Maintenance inspections

B-1 Introduction

Outlines the purpose and types of helicopter maintenance inspections.

B-2 First 25-hour inspection

Details the required tasks for the initial 25-hour service.

B-3 50-hour inspection

Lists the maintenance operations for every 50 hours of service.

B-4 100-hour / 12-month inspection

Specifies tasks for 100-hour or 12-month inspections.

B-5 500-hour / 60-month inspection

Outlines the maintenance required for 500-hour or 60-month intervals.

B-6 Special inspections

Covers inspections triggered by specific events like hard landings.

Section C Airworthiness limitations

C-1 General

Defines the scope of airworthiness limitations for parts and assemblies.

C-2 Limitations

Details specific limitations like fatigue life and inspection intervals.

Section D Other limitations

D-1 Time-in-service records

Emphasizes operator's responsibility for maintaining time-in-service records.

D-2 Manufacturer time limits

Lists time limits set by the manufacturer for airworthiness.

D-3 Overhaul requirements

Specifies assemblies requiring overhaul before prescribed limits.

D-4 Incidents and accident reports

Outlines procedures for reporting incidents and accidents.

Section E Maintenance instructions

E-1 Main rotor

Provides maintenance procedures for the main rotor system.

E-2 Main transmission

Details maintenance instructions for the main transmission gearbox.

E-3 Tail rotor and transmission

Covers maintenance procedures for the tail rotor and transmission systems.

E-4 Flight controls

Outlines maintenance and rigging procedures for flight control systems.

E-5 Engine installation

Details procedures for engine installation and related systems.

E-6 Airframe

Covers maintenance tasks related to the helicopter airframe structure.

E-7 Systems

Describes maintenance for electrical, instrumentation, and avionics systems.

E-8 Miscellaneous

Includes various maintenance tasks not categorized elsewhere.

Section F Trouble shooting

Section G Appendix

G-1 Approved material list

Lists approved materials, greases, oils, adhesives, and sealants.

G-2 Special tools

Identifies special tools required for maintenance actions.

G-3 Tail rotor blade rigging check template

Provides a template for checking tail rotor blade rigging alignment.

G-4 Safety pin table

Contains a table for safety pin dimensions based on bolt diameter.

Section H Flight report models