Why does my H2X THERAPOOL SE have a chlorine odor?
If you notice a chlorine odor in your H2X Hot Tub, it's likely due to excessive chlorine or a low pH level. To resolve this, shock the water with an oxidizer/non-chlorine shock treatment. Additionally, check and adjust the pH level as needed.
How to fix cloudy water in H2X THERAPOOL SE?
Cloudy water in your H2X Hot Tub can be caused by dirty filters, inadequate filtration, unbalanced water chemistry, or old water. Clean the filters with a filter cleaner and adjust the filtration settings. Test and adjust the water chemistry levels. If the water is old, drain the tub, clean the inner shell, and refill it with filtered water.
What to do if H2X THERAPOOL SE Hot Tub causes eye or skin irritation?
Eye or skin irritation in your H2X Hot Tub can be caused by unsanitary water, a total chlorine level above 5 ppm, or poor sanitizer/pH levels. Adjust the water chemistry according to testing results. If the total chlorine level is high, apply an oxidizer/non-chlorine shock treatment. Adjust the pH level as necessary.
How to fix cloudy and green water in H2X THERAPOOL SE Hot Tub?
If your H2X Hot Tub has cloudy and green water, it's likely due to low total alkalinity or low sanitizer levels. Use a pH increaser to raise the total alkalinity. Apply oxidizer/non-chlorine shock treatment and adjust the sanitizer levels.
General| Voltage | 240V |
|---|---|
| Amperage | 50A |
| Insulation | Full Foam |
| Pumps | 2 |
| Water Management System | Yes |
| Lighting | LED |
| Shell Material | Acrylic |
| Pump | 2 |
| Cabinet Material | Synthetic |
| Warranty | 5 years |
Section to record essential ownership information for warranty and service.
Information on finding the swim spa's serial number for identification and registration.
Steps to register the swim spa online for efficient customer assistance.
Essential safety instructions for operation, electrical safety, and health risks.
Precautions for specific user groups and temperature safety for swim spa use.
Details the industry standards and certifications the swim spa adheres to for safety and efficiency.
Guidelines to prevent suction entrapment hazards like hair, limb, and body entrapment.
Definitions for various swim spa components, controls, and features.
Descriptions of key operational systems like pumps, heaters, and control panels.
Details the benefits and installation steps for the EcoPur® Charge filtration system.
Explains essential water chemistry terms like ppm, alkalinity, pH, and sanitizers for water balance.
Explains concepts like sequestering, filtration, defoamers, and calcium hardness.
Explains the necessity of chemicals for maintaining water quality and preventing issues.
Steps for initial filling, balancing water chemistry, and sanitizing the swim spa.
Schedule of routine tasks including daily checks, weekly treatments, and monthly filter cleaning.
Procedures for periodic draining, refilling, and addressing water issues as needed.
Guide to identify and resolve common water quality problems like odor, cloudiness, and foaming.
Target ranges for key water chemistry parameters to maintain a balanced and healthy swim spa.
Step-by-step guide for cleaning swim spa jets and diverter valves to ensure proper function.
Maintenance procedures for laminar flow jets and the ozone system for optimal performance.
Guidance on cleaning and replacing filter elements for optimal water quality and equipment longevity.
Maintenance recommendations for swim spa pillows, cover, cabinet, and optional exercise gear.
Guidelines for cleaning and maintaining stainless steel components to prevent corrosion and maintain appearance.
Procedures for draining, cleaning the shell and divider, and refilling the swim spa.
Diagnosing and resolving issues related to no power, non-operational pumps, and poor jet performance.
Troubleshooting procedures for swim spa heating problems and GFCI breaker trips.
Detailed steps for winterizing the swim spa, including draining and protecting components.
Recommendations for protecting the swim spa shell and components from damage during storage.
Table detailing dimensions, electrical needs, capacity, weight, pumps, and controls for various models.
Guidelines for ensuring adequate access and a suitable, level foundation for the swim spa.
Key considerations for both outdoor and indoor swim spa installations, including environmental factors.
Specific guidelines for partially or fully recessed swim spa installations, focusing on drainage.
Electrical requirements for a single 240V, 50A GFCI service configuration.
Electrical requirements for dual 240V, 50A GFCI service configurations.
Comprehensive steps for setting up the swim spa, including filling, priming, and initial checks.
Introduction to the main screen of the Icon Spa Touch control system and its elements.
Definitions for the icons displayed on the main screen, indicating status and functions.
Functions for panel locking, message display, and controlling swim spa equipment.
Navigating temperature settings, scales, and accessing the main settings menu.
How to view and dismiss messages and alerts displayed on the swim spa control panel.
Guide to adjusting the swim spa's set temperature using the control panel buttons.
Overview of the Spa Screen, displaying and controlling various swim spa equipment like pumps and jets.
How to use common buttons for adjusting values and inverting the display screen.
How to use Back and Save buttons to exit screens and save changes or cancel.
How to navigate through menu screens using page navigation buttons.
How to program settings and configure dual temperature ranges (High/Low).
Details on Ready, Rest, and Circulation modes affecting heating and pump operation.
Guide to the priming mode and essential steps for initializing the swim spa pumps.
Details on pump operation, circulation pump modes, and freeze protection activation.
How the filtration and ozone systems function, including programmed filter cycles.
Information on freeze protection activation and optional clean-up cycle settings.
Importance and steps for setting the swim spa's time-of-day for features like filtration.
How to set start times and durations for main filter cycles (Filter 1 and 2).
Explanation of purge cycles and their role in maintaining sanitary conditions.
Procedures for locking and unlocking the swim spa control panel or specific settings.
How to use Hold Mode to disable pumps during maintenance or service operations.
How to configure temperature units (F/C) and manage reminder messages.
How to set the cleanup cycle duration and select the display language.
Accessing the fault log for troubleshooting and performing GFCI tests.
Details on viewing system model, panel version, software ID, and configuration.
Step-by-step guide for testing the Ground Fault Circuit Interrupter (GFCI) for safety.
Explanations for general messages like temperature status and freeze protection.
Common heater-related messages and troubleshooting steps, including flow checks.
Troubleshooting sensor balance errors and communication issues between control panel and system.
Explains system errors like memory failure, configuration issues, and pumps stuck on.
Common reminders for essential maintenance tasks like checking water chemistry and filters.
Reminders for periodic tasks such as cleaning covers, treating wood, changing filters, UV, and ozone.
How to navigate the MP30 control panel menus using buttons and understanding power-up sequences.
Essential steps for initial setup, including filling the spa and priming the pumps.
Details on pump operation, circulation pump modes, and freeze protection activation.
How the filtration and ozone systems function, including programmed filter cycles.
Guide to adjusting the swim spa's set temperature using the control panel buttons.
Explains Ready, Rest, and 24-hour Circulation modes and their impact on heating.
How to invert the display and adjust main filtration cycle durations.
Explanation of purge cycles and their role in maintaining sanitary conditions.
Explanations for general messages like temperature status and freeze protection.
Common heater-related messages and troubleshooting steps, including flow checks.
Troubleshooting sensor balance errors and communication issues between control panel and system.
Explains system errors like memory failure, configuration issues, and pumps stuck on.
Visual guide to pump and control component placement for the Therapool SE model.
Visual guide to pump and control component placement for the Therapool D model.
Visual guide to pump and control component placement for the Trainer 12 model.
Visual guide to pump and control component placement for the Trainer 15 and 15D models.
Instructions for remote control power, syncing, charging, and essential safety warnings.
Explains the functions of various buttons on the remote control for audio playback.
Steps for pairing Bluetooth devices and controlling volume levels for audio playback.
Instructions for operating the FM radio mode, scanning channels, and saving presets.
How to access the audio menu for sound adjustments and use the Virtual Bass feature.
How the Wave Lighting system activates automatically based on ambient light and manual control.
How to remotely control swim spa operations using the Balboa Water Group Wi-Fi Spa Control App.
Detailed instructions for safely removing and replacing the UV lamp in the Mast3rPur system.
Maintenance procedures for the UV reactor and cleaning the quartz tube, including safety precautions.
Step-by-step guide for the proper installation of the quartz tube into the UV chamber.
Recommendations for cleaning and maintaining the SoftTread floor system, including what to avoid.
Schedule of routine maintenance tasks and a log to document performed service.
To Next Page