How to troubleshoot a Hafco BS-13DS that cannot be started?
If your Hafco Saw machine won't start, first, ensure it's properly plugged in and the power light on the control panel is illuminated. If the motor still doesn't start, the limit switch may have cut the power; make sure the cover is correctly positioned. Finally, check the operation button, push the emergency button and return it to its original position, then release it.
Why is my Hafco BS-13DS blade breaking so much?
Excessive blade breakage in your Hafco Saw can stem from several issues. Ensure the materials are securely clamped in the vise. Adjust the speed and feed settings. If the blade teeth spacing is too large, replace it with a blade that has smaller teeth spacing. For coarse materials, use a blade with slow speed and small teeth spacing. Ensure correct blade tension, adjusting it so the blade barely slips on the wheel. Place the blade in contact with the work after the motor has started. Adjust the wheel alignment if the blade rubs on the wheel flange. Correct any misalignment in the guide bearings. If the blade is too thick, use a thinner one. If cracking occurs at the weld, reweld it, paying attention to welding skill.
What to do if my Hafco BS-13DS Saw blade is dulling quickly?
If your Hafco Saw blade is dulling prematurely, several factors could be at play. If the teeth are too coarse, switch to finer teeth. Too much speed can also cause this issue, so decrease the speed. Inadequate feed pressure is another potential cause; try decreasing the spring tension on the side of the saw. For materials with hard spots or scale, reduce the speed and increase feed pressure. If the material is work hardening, increase feed pressure by reducing spring tension. Replace a twisted blade with a new one and adjust blade tension. Ensure sufficient blade tension by tightening the blade tension adjustable knob. If the blade slides, tighten the blade tension.
Why are teeth ripping from my Hafco Saw blade?
If the teeth are ripping from the blade on your Hafco Saw, it could be due to several reasons. If the tooth is too coarse for the work, use a finer tooth blade. Too heavy pressure or too slow speed can also cause this; decrease the pressure and increase the speed. If the work-piece is vibrating, clamp it securely. If the gullets are loading, use a coarser tooth blade or a brush to remove chips.
Why is my Hafco BS-13DS motor running too hot?
If your Hafco Saw motor is running too hot, consider these possible causes: reduce the tension on the blade if it's too high. Also, reduce the tension on the drive belt if it's too high. If the blade is too coarse for the work, use a finer blade. Conversely, if the blade is too fine for the work, use a coarser blade. If the gears are aligned improperly, adjust them so that the worm is in the center of the gear. Check the oil path if the gears need lubrication. If the cut is binding the blade, decrease reed anti speed.
How to fix crooked cuts with my Hafco BS-13DS Saw?
If your Hafco Saw is making bad, crooked cuts, the feed pressure may be too great; reduce pressure by increasing spring tension on the side of the saw. Ensure that the guide bearings are properly adjusted, with a clearance no greater than 0.001. Increase blade tension if it's inadequate by adjusting the blade tension. Replace the blade if it's dull. Adjust the speed if it's incorrect. Adjust the guide space if the blade guides are spaced out too much. Tighten the blade guide assembly if it's loose. Re-track the blade according to the operating instructions if the blade truck is too far away from the wheel flanges.
Why is my Hafco BS-13DS Saw making rough cuts?
If your Hafco Saw is making bad, rough cuts, decrease the speed or feed if they are too high. If the blade is too coarse, replace it with a finer blade. Adjust the blade tension if it's loose.
What causes unusual wear on the side of my Hafco BS-13DS blade?
If you notice unusual wear on the side or back of your Hafco Saw blade, replace the blade guides if they are worn. Adjust the blade guide bearings according to the operator's manual if they are not adjusted properly. Tighten the blade guide bearing bracket if it is loose.
Why is the blade twisting on my Hafco BS-13DS Saw?
If the blade is twisting on your Hafco Saw, it might be because the cut is binding the blade; decrease reed pressure. Alternatively, there might be too much blade tension; decrease blade tension.
What to do if the saw arm on my Hafco BS-13DS won't raise?
If the saw arm on your Hafco Saw cannot be raised after pushing the raising button, press the emergency stop button and RESET. Check the upper limit switch and stop round position, ensuring the limit switch is always underneath the stop round bar. Check the oil gauge to ensure the oil is in the proper range. Verify the motor revolution direction, ensuring it is in a clock-wise direction.
Rules for operator apparel, eye protection, and general conduct.
Guidelines for operating the machine safely and correctly.
Procedures for adjustments, working environment, and specified usage.
Procedures for maintaining the machine.
Specifies the sound pressure level of the machine.
Describes the interlock switch for the cutting area.
Procedures for unpacking and moving the machine safely.
Steps for correctly installing the machine.
Required space for machine operation.
How to select the correct blade tooth pitch for materials.
Tooth selection for tubing, pipe, and structural materials.
Recommended speeds and feeds for bi-metal blades.
Interpreting chips to adjust feed and speed.
Description of the electrical system and control interface.
Steps for safely starting and stopping the machine.
How to adjust the saw arm's downward movement.
Procedures for adjusting blade speed and belt tension.
Adjusting blade tension and ensuring proper tracking.
How to adjust the cutting width.
Adjusting blade guides and clearing chips.
Information on the blade and coolant flow control.
How to operate and adjust the vise.
Procedure for selecting cutting angles.
Steps for replacing the saw blade.
Description and operation of the hydraulic system.
Information regarding gearbox oil changes and maintenance.
How to lubricate the pivot point.
Operating instructions for the hydraulic unit.
Procedures for cleaning the machine and floor.
Daily checks and tasks for machine upkeep.
Weekly checks and lubrication tasks.
Monthly checks for loose parts and lubrication.
Annual checks for accuracy, wiring, and adjustments.
Causes and corrective actions for machine startup issues.
Reasons for blade breakage and how to fix them.
Causes and solutions for premature blade dulling and wear.
Identifying and resolving motor overheating issues.
Troubleshooting crooked or rough cuts.
Reasons for blade twisting and how to resolve it.
Troubleshooting problems with raising the saw arm.
General| Motor Power | 750W / 1HP |
|---|---|
| Table Size | 460 x 460 mm |
| Weight | 110 kg |
| Voltage | 240V |
| Blade Diameter | 13 mm |
| Cutting Depth at 90° | 130 mm |
| Cutting Depth at 45° | 90 mm |
| No-Load Speed | 800 m/min |
To Next Page
