Haier H2SM- - User Manual

Drawing for the installation of indoor and outdoor units
Necessary Tools for Installation
Driverƽ
Torque wrench
ƽ
(17mm,22mm,26mm)
Nipperƽ
Reamerƽ
Hacksawƽ Pipe cutterƽ
Gas leakage detector orƽ
soap-and-water solution
Hole core drillƽ Flaring toolƽ
Spanner(17,19 and 26mm)ƽ Knifeƽ
Measuring tapeƽ
Indoor Unit
Place, robust not causing vibration, where the body can be supported sufficiently.ƽ
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
ƽ
Place, possible to drain easily, where piping can be connected with the outdoor unit.ƽ
Place,wherecoldaircanbespreadin a roomentirely.ƽ
Place, nearby a power receptacle, with enough space around. (Refer to drawings).ƽ
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
ƽ
In the case of fixing the remote controller on a wall, place where the indoor unit can
receivesignalswhenthefluorescent
ƽ
lampsintheroomarelightened.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is sufficiently ventilated.ƽ
Place,possibletobeartheunit,wherevibrationandnoisearenotincreased.ƽ
Place, where discharged wind and noise do not cause a nuisance to the neighbors.ƽ
Place, where a distance markedƽ

is available as illustrated in the above figure.
Before inserting power plug into receptacle, check the voltage without fail.
The power
sourceisthesameasthe
ƽ
correspondingnameplate.
Install an exclusive branch circuit of the power.
ƽ
Areceptacleshallbesetupin a distancewherethepowercablecanbe
reached.
Donotextendthecablebycuttingit.
ƽ
Power Source
Preparation
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual.
NO.0010531114
Installation Manual of Room Air Conditioner
F
A
C
E
Optional parts for piping
Non-adhesive tape
Adhesive tape
Saddle (L.S) with screws
Connecting electric cable
for indoor and outdoor
Drain hose
Heating insulating material
Piping hole cover
Floor fixing dimensions of the
outdoor unit (Unit:mm)
Fixing of outdoor unit
Fix the unit to concrete or blockƽ
withbolts(10mm)andnutsfirmly
and horizontally.
When fitting the unit to wall
ƽ
surface, roof or rooftop, fix
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
ƽ
house, fix the unit by attaching a
vibration-proof mat.
The marks from to
in the figure are the
parts numbers.
Thedistancebetween
the indoor unit and the
floor should be more
than 2m.
ThemodelsadoptHFCfreerefrigerantR410A
more than
10cm
more than 5cm
more than 10cm
more than 10cm
more than
10cm
more than15cm
more than
60cm
A
G
ƽ
ƽ
A
F
C
E
D
G
B
Arrangement of piping
directions
Rear left
Left
Rear
right
Right
Below
G
Please be subject to the actual product purchased , the above picture is just for your reference.
Attention must be paid to
the rising up of drain hose
113.5
583
113.5
5
.
913
Selection of Installation Place
Unit A
Unit B
To unit A
To unit B

Summary

Preparation

Necessary Tools for Installation

Lists essential tools required for the installation process.

Power Source

Details requirements for connecting the air conditioner to the power supply.

Selection of Installation Place

Provides guidelines for choosing appropriate indoor and outdoor unit locations.

Installation of the Indoor Unit

Fitting of the Mounting Plate and Positioning of the wall Hole

Describes how to mount the plate and prepare the wall for the indoor unit.

Making a Hole on the Wall and Fitting the Piping Hole Cover

Details how to create the wall hole and install the piping cover.

Fixing the indoor unit body

Explains how to securely attach the indoor unit to the mounting plate.

Connecting the indoor;outdoor Electric Cable

Guides the connection of electrical cables between indoor and outdoor units.

Installation of Outdoor Unit

Connection of pipes

Details the process of connecting the refrigerant pipes between units.

Connection

Instructions for connecting the electrical wiring to the outdoor unit.

Attaching Drain-Elbow

Describes how to attach the drain elbow for proper water removal.

Purging Method: To use vacuum pump

Explains the vacuum pump method for purging the refrigerant system.

Power Source Installation

Cutting and Flaring Work of Piping

On Drainage

Provides guidelines for correct drain hose installation and drainage confirmation.

Check Items for Test Run

Lists critical checks to perform before and after the test run.

Haier H2SM- Specifications

General

Brand	Haier
Model	H2SM-
Category	Air Conditioner
Language	English