Haier HSU-10TSV13-SC User Manual

Remote controller
Parts and Functions
Indoor Unit
Outdoor Unit
●
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL
WIRING DRAIN HOSE
4
Display board
Actual inlet grille and Display board may vary from the one
shown in the
manual according to the product purchased
(adjust left and
Vertical blade
right air flow)
Air Purifying Filter
Inlet
(inside)
Emergency
Switch
Horizontal flap
Don't adjust it manually
Inlet grille
5
2
1
6
4
2
1
7
8
33
Outlet
Anion generator
( inside,
only applicable for certain
1
Display board
2
3
Signal receiver
1
emp.display
2
3
Operation mode indicator
1
1. Mode display
Operation mode
FAN
COOL DRY
Remote controller
2.Signal sending
3.display SWING
4.display FAN SPEED display
LO MED HI
AUTO
circulated
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
Operation mode
Remote controller
QUIET TURBOSLEEP HEALTH
Loading of the battery
1
2
3
4
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
Note:
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
wireless telephone is installed in the
room, the recei
ver is apt to be disturbed in receiving
the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up
Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
reload several minutes later.
(adjust up and down air flow
1
2
3
4
5
9
10
11
12
13
14
15
16
17
8
22
23
24
25
19
20
21
18
7
6
SLEEP
TIME
ON
SWING
EXTRA
FUNCTION
LOCK
LIGHT
R E S E T
MODE
SLEEP
I FEEL
HEALTH
TIMER
SELF
CLEAN
HEALTH
AIRFLOW
1
2
3
4
5
9
10
11
12
13
14
15
16
8
22
23
24
25
19
20
21
18
7
6
17
1. Mode display
Operation mode
FAN
COOL DRY
Remote controller
LO MED HI
AUTO
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP HEALTH
Be sure that the loading
26
9.TURBO/QUIET button
10.SELF CLEAN button
11.COOL button
12.SWING LEFT/RIGHT button
(only applicable for certain models)
13.FAN SPEED button
14.HEALTH button/DRY button
(Refer to the actual remote control layout
for specific functions)
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.DRY button/ECO button
(Refer to the actual remote control layout
for specific functions)
20.TEMP button
21.SWING UP/DOWN button
22.TIME OFF/ON button
23.EXTRA FUNCTION button
Function :FAN---Healthy airflow position1---
Healthy airflow position2
Function :FAN --- Health
24.CONFIRM/CANCEL button
Function :Setting and cancel to the timer
and other additional functions.
25.RESET button
When the remote controller appears
abnormal,use a sharp pointed article to
press this button to reset the remote.
9.TURBO/QUIET button
10.SELF CLEAN button
11.MODE button
12.SWING UP/DOWN button
13.FAN SPEED button
14.I FEEL button
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.ECO button
20.TEMP button
21.SWING LEFT/RIGHT button
(only applicable for certain models)
22.HEALTH AIR FLOW button
23.CONFIRM/CANCEL button
Function :Setting and cancel to the
timer and other additional functions.
24.TIMER button
25.HEALTH button
26.RESET button
When the remote controller appears
abnormal,use a sharp pointed
article to press this button to reset
the remote.
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
2.Signal sending
3.display SWING
4.display FAN SPEED display
CONFIRM
CANCEL
TURBO/QUIET
LOCK
LIGHT
R E S E T
TIME
OFF
CONFIRM
CANCEL
COOL
SELF
CLEAN
TURBO/QUIET

Haier HSU-10TSV13-SC Specifications

General

Brand	Haier
Model	HSU-10TSV13-SC
Category	Air Conditioner
Language	English