Harman Kardon Citation II - Page 22

20
Check
( )
( )
Cut leads to
½
˝ on a 270 ohm
½
watt 10% resistor (red-violet-brown-silver) and connect between
V7-6 (NS) and V7-4 (S).
In the same manner, connect the following:
( )
( )
270 ohm
½
watt 10% resistor (red-violet-brown-silver) from, V8-6 (NS) to V8-4 (S).
( )
( )
270 ohm
½
watt 10% resistor (red-violet-brown-silver) from V9-6 (NS) to V9-4 (S).
( )
( )
270 ohm
½
watt 10% resistor (red-violet-brown-silver) from V10-6 (NS) to V10-4 (S).
The output transformer secondaries will now be wired.
Route the following wires from the right output transformer and dress as shown in Pictorial #6.
( )
( )
Cut the black lead to required length, strip
¼
˝ and tin. Connect to T2-G (NS).
( )
( )
In the same manner, cut orange lead to required length. Connect to T2-4 (S).
( )
( )
Cut yellow lead to required length. Connect to T2-8 (S).
( )
( )
Cut green lead to required length. Connect to T2-16 (NS). Tape leads together.
Similarly, route the following leads from the left output OT1 transformer, and dress as shown.
( )
( )
Cut black lead to required length. Connect to T1-G (NS).
( )
( )
Cut orange lead to required length. Connect to T1-4 (S).
( )
( )
Cut yellow lead to required length. Connect to T1-8 (S).
( )
( )
Cut green lead to required length. Connect to T1-16 (NS). Tape leads together.
( )
( )
Connect a bare wire from T1-G (S) to T3-2 (NS). (See Pictorial #7.)
( )
( )
Connect a .039 mfd capacitor (marked on body) from T3-1 (NS) to T1-16 (NS).
( )
( )
Connect a 39 ohm 1 watt 10% resistor (orange-white-black-silver) from T3-2 (S) to T3-1 (S).
( )
( )
Connect a bare wire from T2-G (S) to T4-2 (NS).
( )
( )
Connect a .039 mfd capacitor (marked on body) from T4-1 (NS) to T2-16 (NS).
( )
( )
Connect a 39 ohm 1 watt 10% resistor (orange-white-black-silver) from T4-2 (S) to T4-1 (S).
( )
( )
Insert line cord in hole on rear of chassis. Press in until it snaps in place.
( )
( )
Connect the black wire to lug # 1 of the AC receptacle (S).
( )
( )
Connect the white wire to lug #2 of the AC receptacle (S).
Place the electrolytic bracket in the chassis and align with the mounting holes. The harness should pass
through the smaller round cut-out. The leads from the power transformer should pass through the larger round
cut-out. Move the large grommet which holds the power transformer leads up to the large round cut -out of the
bracket. See Pictorial #7.
( )
( )
Split the small grommet and slip it over the harness.
( )
( )
Now insert the grommets in the cut-outs of the electrolytic bracket and maneuver the bracket to
realign with the mounting holes. Be sure no wires are caught under the bracket. Bolt to chassis using
#6-32 hardware, lockwasher under head of screw.
( )
( )
Connect the two brown and two black leads emerging from center of harness to C2 on the bracket
(S). (Also solder C2 to bracket.)
( )
( )
Connect white/orange lead from power transformer to El (S).
( )
( )
Connect white lead from power transformer to the positive terminal of selenium rectifier SR1 (S).
( )
( )
Connect red/white lead from power transformer to A3 (S).
( )
( )
Connect red lead from power transformer to T5-1 (S).
( )
( )
Connect free end of 3
½
˝ black lead attached to V8-X6 to C-X9 (S).
Route the remaining leads of the right output transformer OT2 as shown in Pictorial #7.