Harman PC45 - Manual Start Up; Starting the Fire Manually; Manual Burning Fuel

17 pC 45 Corn/pellet Stove
3-90-02686R29_05/14
Manual Start Up
Corn Burnpot Setup
Fig. 25
Pellet Burnpot Setup
Fig. 26
Fig. 24
6
4
5
2
3
1
MAX.
CORN
TEST
F
E
E
D
A
D
J
U
S
T
E
R
P
E
L
L
E
T
O
N
L
Y
C
O
R
N
-
P
E
L
L
E
T
Starting the Fire / Igniter Switch to "MANUAL"
Make sure the unit is plugged into a 120 VAC, 60 Hz
electricalsource.The power light should be theonlylight
lit.Anytimethereisinterruptioninpoweratthereceptacle,
thecombustionblowerwillrunfor1minuteafterthepower
isregained.
Burning Corn
1. Turn the FeedAdjuster to the desired feed rate,
approximately#2.
2. TurntheModeSelectorto"OFF"andthentothedesired
mode.Thiswillresetthecontrolandstartthecombustion
motor.
3. TurntheTemperatureDialtothedesiredsetting.
4. Cleantheburnpotandhousing,ifnecessary.
5.Filltheburnpotwithcornuptotheaugershaft.Thenplace
pelletsontopofthecornashighastheshelfarea.See
cornburnpotshownonleft.
6. Addstartinggelontopofthepellets,stirgelintothepellets
andcornforfasterlighting.
7. Light the starting gel with a match and close thedoor.
Operation will begin when the re reaches the proper
temperature.
8. Fill the hopper with corn and remove the ashes as
required.
Burning Pellets
1. Turn the FeedAdjuster to the desired feed rate,
approximately#4.Fig.24
2. TurntheModeSelectorto"OFF"andthentothedesired
mode.Thiswillresetthecontrolandstartthecombustion
motor.
3. TurntheTemperatureDialtothedesiredsetting.
4. Cleantheburnpotandhousing,ifnecessary.
5. Filltheburnpotwithpelletssothattheaugertubeopening
iscoveredandslopesawayfromtheaugertubeopening.
Seepelletburnpotshownonleft.Ifusingcornburnpot
setup,lltosamelevelascornabove.
6. Addthestartinggelontopofthepellets.Stirthegelinto
thepelletsforfastlighting.
7. Light the starting gel with a match and close thedoor.
Operation will begin when the re reaches the proper
temperature.
8. Fill the hopper with pellets and remove the ashes as
required.
Shut-Down Procedure
To kill the re or stop burning the stove, turn the Mode
Selectorto "OFF".Thiswillcausetheretodiminish and
burnout.Whenthereburnsoutandthestovecoolsdown
everythingwillstop.NOTE: The combustion blower motor
will be the last component to stop. Thisinsuresthatall
fuel in the burnpot and ashes located in the ash pan are
completelycoldbeforeshutdownofthecombustionmotor.
Ifyoupulltheplugtoshutdownthestove,allmotorswillstop.
Thismaycauseincompletecombustionandsmokeinthe
rebox.Iftheloaddoorisopenedthesmokemayescape.
Thebestwaytoshutdownthestoveissimplyletitrunout
offuel,thenthestovewillshutdownautomatically.
WARNING
!
NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR "FRESHEN UP " A
FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS
WELL AWAY FROM THE HEATER WHILE IN USE.