Hawksmoor Toolstation SLM32F-ZE

Questions and Answers

H
harrisdanielleAug 7, 2025
How to troubleshoot Hawksmoor Toolstation SLM32F-ZE Lawn Mower that does not start?
- J
  Jennifer DaviesAug 7, 2025
  If your Hawksmoor Lawn Mower doesn't start, first, make sure it's properly connected to a power supply. If it is, check that you've pressed the lock-off button before attempting to start it with the start lever. Also, inspect the fuse and replace it with a 13 AMP fuse approved to BS1362 if it's blown.
C
Christopher VasquezAug 17, 2025
Why Hawksmoor Lawn Mower does not reach full power?
- P
  pashleyAug 17, 2025
  If your Hawksmoor Lawn Mower isn't reaching full power, the issue might be with the extension cord you're using; ensure it's suitable for operating the lawn mower. Alternatively, the power source, such as a generator, could have too low a voltage; try connecting to another power source. Also, check the air vents and clean them if they are blocked.
K
Kimberly PittmanAug 27, 2025
What to do if Hawksmoor Toolstation SLM32F-ZE Lawn Mower gives unsatisfactory result?
- P
  Phillip WhiteAug 27, 2025
  If you're getting an unsatisfactory result with your Hawksmoor Lawn Mower, it might be due to a worn cutting device, which should be replaced. Also, ensure you're not trying to cut materials beyond the product's capacity. Finally, check and adjust the cutting height, as it may be incorrect.

Summary

Explanations and Symbols, Cautions and Warnings

Explanation of Symbols

Explains the symbols and signal words used in the manual and on the product.

Important Safety Warnings

Proper Use

Details on how to operate the lawnmower correctly and safely.

Safety Notes

Important safety advice and precautions for operating the appliance.

Work Area Safety

Guidelines for maintaining a safe working environment around the lawnmower.

Personal Safety

Recommendations for personal protective equipment and safe attire.

Operational Safety

Safety measures related to the operation of the lawnmower.

Product Description and Identifications

Assembly and Operating Instructions

Assembly

Step-by-step instructions for putting the lawnmower together.

Connecting to the Power Supply

Operation

Cutting Height Adjustment

How to adjust the cutting height of the lawnmower.

Grass Collection Box

Instructions for attaching, emptying, and refitting the grass collection box.

Switching On;Off

Steps for turning the lawnmower on and off.

Mowing

Guidelines and techniques for effective mowing.

Care and Cleaning

Maintenance

General guidelines for maintaining the lawnmower.

Maintenance After Each Use

Steps for cleaning and maintaining the lawnmower after each use.

Spare Parts;Replacement Parts

Information on available spare parts and how to obtain them.

Underbody and Cutting Device

Instructions for cleaning and checking the underbody and cutting device.

Replacing the Blades

Detailed steps for safely replacing the lawnmower blades.

Repair

Guidance on when and how to get the product repaired.

Transportation

Safe procedures for transporting the lawnmower.

Cleaning

Detailed instructions for cleaning the lawnmower deck and general upkeep.

Storage

Guidelines for storing the lawnmower safely.

Declaration of Conformity; Performance

This document provides the user's instructions for the Hawksmoor 1200W Electric Lawnmower, SKU: 62767, manufactured for Toolstation. It covers assembly, operation, maintenance, and safety warnings for the product.

Function Description

The Hawksmoor 1200W Electric Lawnmower is designed for domestic use to cut grass. It features a 32cm cutting width and a 30L grass catcher volume, making it suitable for maintaining lawns. The lawnmower is electrically powered and requires connection to a mains supply, preferably protected by a Residual Current Device (RCD) with an operating current less than 30mA. The product is intended for private use and not for commercial applications.

Important Technical Specifications

Model: SLM32F-ZE
Input voltage rating: 230-240V~, 50Hz
Input power: 1200 W
No load speed: 3500/min
Max. cutting width: 320mm
Cutting height: 25/45/65mm, 3 adjustments
Grass catcher volume: 30L
Safety class: Class II /
Weight Approx.: 8.2kg
Protection degree: IPX4
Sound pressure level LpA: 73.7dB(A) K=1.12 dB(A)
Sound power level LWA: 93.7dB(A) K=1.12 dB(A)
Guaranteed sound power level LWA: 96dB(A)
Emission pressure level: 87dB(A) K=3dB
Hand arm vibration ah: ≤2.5 m/s²
Uncertainty K: 1.5m/s²
Cable: H05VV-F, 2x0.75mm², 10m, BS plug

The sound values are determined according to EN 60335-2-77, EN ISO 11201, and EN ISO 3744. Ear protection is necessary if the sound intensity level for the operator exceeds 80 dB(A). The declared vibration value is measured according to EN 60335-2-77 and can be used for comparison and preliminary exposure assessment.

Usage Features

The lawnmower is designed for ease of assembly and operation.

Assembly: The lower and upper handles are assembled by inserting them into supports and securing them with screws, knobs, and bolts. The power cord is fixed to the handle using cord clips. The grass collection box is assembled by clipping its upper and lower halves together and then fitting the handle. Finally, the grass collection box is hooked into position by lifting the safety rear flap.
Connecting to Power: An extension cord suitable for outdoor use and protective against splashing water is recommended (rubber insulated 60245 IEC53 or polyvinyl chloride insulated 60227 IEC 53, ≥ 1.5mm²). Always use an RCD-protected supply.
Cutting Height Adjustment: The lawnmower offers three cutting height adjustments (25/45/65mm). To adjust, release the start lever, disconnect from power, pull out the rear and front shafts, and place them into the desired slot. Ensure both shafts are at the same level and click back into place. For high grass, it's recommended to start with the maximum height and then make a second cut at a lower height.
Grass Collection: The 30L grass collection box should always be attached during operation. It features a grass full indicator that floats when empty or partially filled and falls down when full. The box should be emptied frequently, ideally when half full, to maintain performance.
Switching On/Off: To start, press the lock-off button (1) and then pull the switch lever (2) towards the handle. Release the lock-off button once the product is running. To switch off, release the switch lever. The cutting device will continue to rotate for a short period after switching off.
Mowing Technique: Mow in daylight or good artificial light, avoiding wet grass. Always ensure good footing on slopes and walk, never run. Mow across slopes, not up and down, and exercise caution when changing direction. Do not mow excessively steep slopes. Use extreme caution when reversing or pulling the product. Stop the blades for transportation or when crossing non-grass surfaces. Do not tilt the product when starting the motor unless necessary, and only lift the part furthest from the operator. Keep hands and feet away from rotating parts and the discharge opening. Do not transport the product while connected to mains power. Stop the product and remove the plug before leaving it unattended, clearing blockages, or unclogging the chute. Never cut more than one-third of the grass length for a healthy lawn. Mow in slightly overlapping, straight rows. Circle around flower beds.
Safety: Always wear appropriate Personal Protective Equipment (PPE) including eye protection, ear protection, respiratory equipment, safety boots, and gloves. Avoid loose clothing or jewellery. The appliance should not be used by children or young people under 16, or by anyone unfamiliar with the instructions. An RCD is mandatory for mains supply connection.

Maintenance Features

Regular maintenance is crucial for safe operation and prolonging the product's life.

General Maintenance: Always switch off, disconnect from power, and allow the product to cool before any inspection, maintenance, or cleaning. Keep the product clean by removing debris after each use and before storage. Inspect for worn or damaged parts before each use and do not operate if any are found. Only qualified specialists should perform repairs beyond the scope of these instructions.
After Each Use: Clean the product with a dry cloth and a brush for hard-to-reach areas. Clean air vents with a cloth and brush. Remove stubborn dust with high-pressure air (max. 3 bar). Check for damage or wear and repair as per instructions or take to an authorised service centre. Do not use chemicals, alkaline, abrasive detergents, or disinfectants. Do not spray with water, as it can damage the switch unit and motor.
Underbody and Cutting Device: Keep the underbody and cutting device clean. Periodically check nuts and bolts for tightness. The cutting device (blade) will wear over time, especially in sandy conditions, reducing efficiency. Replace worn or damaged blades with a new one of the same type (part number 1466ZE0051). Blades should be replaced after 50 hours of mowing or 2 years, whichever comes first. Lubricate the cutting device with light machine oil after each use.
Replacing Blades: Always unplug the lawnmower and wear gardening gloves. Loosen the bolt anticlockwise with a wrench to remove the cutting device. Reattach the new blade, ensuring correct alignment, and tighten the bolt clockwise to 16-20 Nm.
Power Cord: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons.
Storage: Clean the product, store it and its accessories in a dry, frost-free place, inaccessible to children (ideal temperature 10°C to 30°C). Use original packaging or a suitable cover to protect against dust. Fold the upper handle for compact storage.

The document also includes a troubleshooting guide for common issues like the product not starting, not reaching full power, or unsatisfactory cutting results, along with possible causes and solutions. A Declaration of Conformity is provided, stating compliance with relevant Community harmonization legislation and standards. Environmental information advises on proper disposal of waste electrical products. Customer support contact details are provided for assistance.