Home
HBM
Scales
WE2107 Series
HBM WE2107 Series User Manual
4
of 1
of 1 rating
152 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
I1820-1.3 en
WE2107
Communication commands
Operating Manual
2
Table of Contents
Default Chapter
3
Table of Contents
3
Safety Information
4
1 Introduction and Appropriate Use
5
2 Command Set for the WE2107
6
Complete Menu Structure and Commands
7
Command Format
14
Responses to Commands
15
Responses to Input
15
Responses to Parameter Queries
16
Responses to Incorrect or Unknown Commands
16
Output Types for Measured Values
17
Password Protection Parameters
17
Command Overview (Alphabetical Order)
18
3 Individual Command Descriptions
20
Composition of a Character
20
Interface Commands (Asynchronous, Serial)
20
Address
22
Baud Rate
23
Configurate Output Format (Output Format for Data Outputs)
24
Binary Measurement Format
25
ASCII Measurement Format (COF4)
26
Select (Selecting of WE2107 in Bus Mode)
27
Factory Default Curve
29
Setting the Characteristic Curve
29
Setting the Factory Default Curve with SZA
29
Effect of the SFA Command on the Factory Default Curve
30
Effect of the SZ Command on the Factory Default Curve
30
Sensor Zero Adjust
31
Sensor Fullscale Adjust (Factory Default Curve Full Scale)
32
Manual Input of the Nominal (Rated) Value Via SZA/SFA
33
Calculating the Internal Correction Factor
34
G‐Correction Factor (G‐Factor Correction, Calibration Location)
34
Acceleration Correction User
35
Scale Characteristic Curve and Output Scaling
36
Setting the User Characteristic Curve
37
Load Cell Dead Weight (Scale Curve Zero Point)
38
Load Weight (Scale Characteristic Curve Full Scale)
39
Manual Input of the Nominal (Rated) Value Via LWT
40
Calibration Weight
41
Nominal Output Value (Resolution of the Scale Characteristic Curve)
43
Engineering Unit (Unit of Measurement)
44
Resolution (Display Resolution, Increment)
45
Decimal Point Position
46
Motion Detection
47
Multi Range Mode 1 (2‐Range Weighing Display)
48
Multi Range Mode 2 (3‐Range Weighing Display)
49
Settings for Linearization
50
Linearization Measured Values (Input Values Linearization Curve)
51
Linearization Nominal Values (Output Values Linearization Curve)
52
Settings for Measuring Mode
53
Amplifier Filter (Filter Selection Cut-Off Frequencies)
54
Filter Characteristics FMD0
55
Filter Characteristics FMD1
55
Filter Mode Selection
56
Automatic Zero Tracking
57
Zero Setting (Initial Zero Setting on Start‐Up)
58
Commands for Measuring Mode
59
Measured Signal Value (Measurement Query)
60
Output Format Measured Value at Max. Capacity
61
Preparing for Data Output
61
ASCII Output (COF4)
62
Measurement Status
63
Measured Internal Signal Value (Measurement Query)
64
Clear Dead Load (Set to Zero)
66
Tare with the Actual Gross Value
67
Tare Value
68
Tare Set (Gross/Net Selection)
70
Special Functions
71
Define Password
72
Set Password (Write Enable for All Password Protected Parameters)
73
Restart (Reset Electronic)
74
Identification of Electronic Type and Serial Number
75
Transmit Device Data (Back up Device Parameters)
76
Error Status
78
ADC Overflow (ADC Overflow / Underflow Counter)
81
Sensor Overflow (Sensor Overflow / Underflow Counter)
82
Commands for Legal for Trade Applications
83
Legal for Trade Switch
84
Trade Counter (Legal for Trade (Calibration) Counter)
85
Commands for Setup the Control of an External Display
86
Function UART2 (Printer / External Display Protocol)
87
External Display Protocol
88
External Display Start Character
92
External Display End Character 1
93
External Display End Character 2
94
External Display Check Sum
95
Commands for Setup the Print Function
96
Print Protocol Via Second Serial Link
97
Escape Sequences for the Print Protocol
98
Print Empty Lines before Printing (Print Empty Lines before Printing)
99
Print Empty Spaces in each Line
100
Print Identification Counter
101
Print Strings for the Print Protocol
102
Print Empty Lines at the End of Printing
103
Start Hard Copy Via Second Serial Link
104
Commands for Set up the Real Time Clock
105
Time Date (Real Time Clock Date)
106
Time (Real Time Clock)
107
Time Mode (Real Time Clock Mode)
108
Commands for Setup the Buttons, Digital Inputs
109
Menu Access Level (Access Level for the Parameter Menu)
110
Button Function Short Push
111
Button Function Long Push
113
Function Digital Inputs
115
Tilt Delay Time for Digital Input IN1
117
Commands for Setup the Filling Control / Limit Switches
118
Short Description of the Application Platform Scale
119
Short Description of the Application Dosing Control (SFU1)
120
Cycles of Dosing
121
Short Description of the Application Tank Weighing Control (SFU2)
122
Task Filling the Tank
123
Task Portion Weighing (Dosing)
123
Short Description of the Application Tank Weighing Control (SFU3)
125
Task Emptying the Tank (Only for Service Purposes)
125
Scale Function (Activate Filling / Dosing Function)
126
Limit Values Switches
127
Start Dosing / Portion Weighing
129
Tare Delay Time Portion Weighing / Dosing Process
130
Residual Flow Time, Filling / Dosing Process
131
Maximum Filling Time, Filling / Dosing Process
132
Emptying Time, Filling / Dosing Process
133
Break Dosing / Filling / Emptying Processes
134
Dosing Result Portion Weighing
135
Number of Dosing Results (Dosing Counter)
136
Total Weight of Dosing Results
137
Clear Total Weight and Counters
138
4 Communication Examples
139
All the We's Are Connected to the Bus
139
Connecting We's to the Bus
139
Making Settings for Bus Mode
139
Setting the Data Output
140
Setting the Baud Rate
141
Determining Bus Occupation (Bus Scan)
143
Measurement Query in Bus Mode
144
Setting a Parameter in All the Connected We's
145
Index
146
Other manuals for HBM WE2107 Series
Quick Start Guide
76 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the HBM WE2107 Series and is the answer not in the manual?
Ask a question
HBM WE2107 Series Specifications
General
Accuracy class
III
Maximum number of verification intervals
3000
Protection class
IP67
Material
Stainless steel
Rated output
2 mV/V
Output resistance
350Ω ±3Ω
Related product manuals
HBM WE2107
152 pages
HBM WE2108 Series
72 pages
HBM DIS2116
92 pages