Heath Zenith SECUR360 9309

Questions and Answers

W
wpopeAug 1, 2025
Why does my Heath Zenith SECUR360 9309 Flood Light flash on and off?
- O
  ocastanedaAug 2, 2025
  If your Heath Zenith Flood Light is flashing on and off, consider these solutions: * Reposition the lamp heads away from the motion sensor. * Decrease the sensitivity setting or reposition the motion sensor. * If in TEST mode, remember the light only stays on for 5 seconds; set the “Full Brite Setting” in the app to the 1, 5, or 20 minute setting. * Relocate the light fixture away from the meter.
H
huntertimothyAug 6, 2025
Why do the lights turn off too late in Dusk-to-Dawn setting for my Heath Zenith Flood Light?
- M
  Michelle StricklandAug 6, 2025
  If your Heath Zenith Flood Light turns off too late in Dusk-to-Dawn setting, it might be because the light fixture is installed in a relatively dark location. Consider relocating the light fixture or using the 3 hour or 6 hour setting.
N
Nicholas FisherAug 10, 2025
Why does my Heath Zenith Flood Light stay on continuously?
- T
  Teresa GreenAug 10, 2025
  If your Heath Zenith Flood Light stays on continuously, here are a few things to try: * Decrease the sensitivity setting or reposition the motion sensor. * Use the app to set the light to “AUTO” or “OFF” mode. * Ensure you are not using a dimmer or timer; replace it with a standard on/off wall switch if you are. * Make sure the light fixture is installed on a circuit without motors, transformers, or fluorescent bulbs.
A
Anthony MooreAug 14, 2025
What to do if my Heath Zenith SECUR360 9309 will not come on?
- M
  Michael CrawfordAug 14, 2025
  If your Heath Zenith Flood Light isn't turning on, try the following: * Make sure the light switch is turned on. * Check and replace the fuse or turn the circuit breaker on. * Re-install the light fixture to the mounting plate. * Check again after dark. * Verify that the wiring is correct. * Re-aim the motion sensor to cover the area you want it to detect. * Increase the sensitivity setting. * Use the app to set the light to “AUTO” mode.
J
John ThompsonAug 18, 2025
Why does my Heath Zenith SECUR360 9309 Flood Light come on for no apparent reason?
- L
  lynchautumnAug 19, 2025
  If your Heath Zenith Flood Light activates unexpectedly, it could be due to several factors: * Try decreasing the sensitivity setting or repositioning the motion sensor. * Also, avoid using a dimmer or timer to control the light fixture; instead, use a standard on/off wall switch. * Note that the light fixture might be operating normally under these circumstances.
J
jay92Aug 23, 2025
Why does my Heath Zenith SECUR360 9309 flash once then stay off in manual mode?
- C
  christopherrogersAug 23, 2025
  If your Heath Zenith Flood Light flashes once and then stays off in manual mode, it's likely because the motion sensor is detecting light from the light panels. Reposition the light panels to keep the area below the motion sensor relatively dark.
R
rebeccahessAug 27, 2025
How to remove wires from the mounting plate of my Heath Zenith SECUR360 9309 Flood Light?
- J
  Joshua NortonAug 28, 2025
  If you're having trouble removing the wires from the mounting plate of your Heath Zenith Flood Light because the mounting plate connectors won't release them: * Turn OFF power to the light fixture. * Twist the wires back and forth as you pull them from the mounting plate. Note that these push-in terminals are not designed for reuse.

Summary

Wiring the Mounting Plate

Connecting Solid Copper House Wire

Detailed steps for wiring solid copper house wire to the mounting plate.

Connecting Stranded Copper House Wire

Instructions for using a pigtail to connect stranded house wire to the mounting plate.

Final Assembly

Testing and Adjustments

DualBrite Duration

Reset Button

Care and Cleaning

Specifications

Troubleshooting Guide

Technical Service

One Year Limited Warranty

Heath Zenith SECUR360 9309 Specifications

General

Type	Flood Light
Model Number	9309
Product Name	SECUR360
Brand	Heath Zenith
Light Source	LED
Lumens	1800
Color Temperature	5000K
Beam Angle	120 degrees
Motion Detection Range	up to 70 feet
Motion Sensor Type	PIR
Power Source	Hardwired
Operating Voltage	120V AC
Weather Resistance	IP65
Mounting Type	Wall mount
Weight	2.2 lbs
Adjustable Sensitivity	Yes
Light Color	White