Heath Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light User Manual (English)

Questions and Answers:

M
Michael BallardJul 29, 2025
Why won't my Heath Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light come on?
- D
  Danny ColeJul 29, 2025
  Several factors could prevent your Heath Zenith light fixture from turning on: * The light switch might be off. Check to ensure it is on. * The light bulb may be loose or burned out. Inspect and replace if necessary. * A fuse could be blown, or the circuit breaker might be off. Examine and reset them. * The daylight turn-off feature might be active. Wait until it is dark to test. * Incorrect wiring could be the issue, especially if it's a new installation. Verify the wiring. * The sensor may need re-aiming to cover the desired area. Adjust the sensor accordingly.
G
Gary SmithAug 2, 2025
Why does my Heath Zenith Light Fixture stay on continuously?
- D
  dudleymichaelAug 2, 2025
  There are a few reasons why your Heath Zenith light fixture might remain on: 1. A lamp might be too close to the sensor or pointed at nearby objects, causing heat to trigger the sensor. Try repositioning the lamp. 2. The light control could be directed towards a heat source, such as an air vent or a heat-reflective surface. Reposition the sensor and reduce the range. 3. The light control might be in Manual Mode. Switch it to Auto.
P
Patrick HughesAug 6, 2025
Why does my Heath Zenith Light Fixture come on for no apparent reason?
- G
  Gerald NguyenAug 6, 2025
  Your Heath Zenith light fixture might activate unexpectedly due to these reasons: * The light control could be detecting small animals or car traffic. Try re-aiming the sensor. * The range might be set too high. Reduce the range setting. * The DualBrite® Timer could be enabled. Turn off the DualBrite® Timer.
S
smithrickyAug 11, 2025
What to do if my Heath Zenith Light Fixture lights flash on and off?
- M
  Michael PerryAug 11, 2025
  If your Heath Zenith light fixture is flashing, consider these potential causes: * Heat or light from the lamps might be triggering the light control. Reposition the lamps away from the sensor. * Heat reflected from other objects could be affecting the sensor. Try repositioning the sensor. * The light control might be in Test mode and warming up. Turn Boost off. * The light control could be in Flash mode. Select Normal or Soft mode to disable flash mode.
K
Kimberly RamirezAug 15, 2025
Why does my Heath Zenith Light Fixture come on in daylight?
- G
  Gabriela MorganAug 15, 2025
  Your Heath Zenith light fixture might be activating during the day because: * The light control may be installed in a relatively dark location. Reposition the light control. * The light control is set to Test mode. Switch the control to an ON-TIME position.
D
Danielle BoydAug 19, 2025
Why does Heath Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light Light Fixture turn off too late in Dusk-to-Dawn setting?
- P
  Peter OdonnellAug 19, 2025
  If your Heath Zenith light fixture turns off too late in Dusk-to-Dawn setting, it might be because the sensor is in a relatively dark location. Relocate the sensor or use the 3-hour or 6-hour setting.
V
vroseAug 23, 2025
What to do if Heath Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light flashes once, then stays off in Manual Mode?
- J
  Jill MillerAug 25, 2025
  If your Heath Zenith light fixture flashes once and then remains off in Manual Mode, it could be that the sensor is detecting its own lights. Reposition the lamps to ensure the area below the sensor remains relatively dark.