)
Strip
the ends of a 3"
length of
hookup wire.
Connect
one end
to
AA1
(NS).
Connect
the
other end to
CC1
(NS).
Dress
to chassis.
(r,)
Cut the
Ieads
of a.01 mfd disc
ceramic capacitor
to3/8".
Connect it between CC1
(NS)
and CC2
(NS).
(
r[
Strip the ends of a 5"
Iength
of
hookup wire.
Connect from AA2
(NS)
to 84
(S1).
I
(.1)
strip the ends of a
6" length of
hookup wire. connect from
CCl
(NS)
to DDz
(NS).
j
(
Jj
Cut the leads of a
100 KQ
(brown-black-ye
llow) resistor to 3/8".
Connect
one
lead to BBI
-
(NS).
Connect the
other lead to
BB2
(S2).
t
(
.'l
Cut
and dress the leads
of a 150O
(brown-green-brown)
I watt resistor as shown in
Pictorial
?.
Connect
one lead to 83
(NS).
Connect the other
to the
pin
shield
(S1).
(.1
Cut the
leads of a .01 mfd disc
capacitor to 3/8"
and connect between
83
(S2)
and
the
pin
shieid
(S1).
Position
as shown.
(
{
C"t one
lead of a 10Q
(brown-black-black\
l/2
watt
resistor to
3/8" and
eonnect
it to E}2
-
(Sl).
Connect
the other
lead
to
BB1
(NS).
(
I
Cut
the leads of a .01 mfd disc
ceramic
capacitor
to 3/8".' Connect one
lead to Bg
(NS).
-'
Connect
the other lead to the
pin
shield
"E}"
(S1)
as shown in Pictorial
?.
l
(
{)
Cut
one lead of a 10 KQ
(brown-black-orange)
1
watt
resistor
to
1 L/4".
Connect
this iead
to Bg
(S2).
Position as
shown and
use sleeving.
(-J
Cut
the
remaining
lead of the above
10
KO resistor to 3/4" and
connect it to DD2
(NS).
(.,,)
Cut the Ieads ofa .01mfd
discceramic
capacitor
to 3/8". Connect one
lead
to
DD1
(S2)
and
I
the other lead to DD2
(NS).
I
(;)
Mount the
2.5 mh
RFC,
45-14,
at
the hole near
DD2. Place a #6
lockwasher
on the 6-32
x
3/8"
RHMS andsecure the
RFC
as shown, using
a #6
fiber
washer between
the
choke and
the
chassis.
Be careful
not to
break
ceramic
form
when securi.ng.
i
N)
Using
#20 bare wire, connect
DD2
(S4)
to
RFC1
(Si).
(
1$
Connect
the
parasitic
choke, 45-19, between
B?
(Sl)
and
FFC2
(NS).
(
)
Identifyeach
driver
slug tuned coil byits color dotand insert it in
its
proper
location on the
chassis,
as indicated in Pictorial 7. Orient
each coil
so
its
locating lug
enters the
locatini
hole
provided.
i
({
)
Connect
one end of each
of 5 lengths
of hookup
wire to lug
2
of each driver
coil,
as follows:
'tA
t/4"
length to Ll-2
(S1)
(80
meters)
\8
1/4" length to L2-2
(S1) (40
meters)
Y
3/4"
length to
L3-2
(S1) (20
meters)
,"9
l/a" length to L4-2
(S1)
(
15
meters)
-2"
length to L5-2
(S1) (10
meters)
Leave
the other ends free
temporarily.
(.f
Insert
a 2 3/4" Iength of
#16 bare wire through
the #1 Iugs
of
all of the driver coils
(Ll
through
L5).
Solder each connection, except
L1-1.
Leave
3/8"
of
the wire extending
from
Ll-1 for connection
purposes.
PaEe 32
To Next Page
Loading...
