Helion conquest 10MT XB

Questions and Answers

A
Andre ValentineAug 14, 2025
What to do if my Helion conquest 10MT XB suddenly stops running?
- T
  Terri LewisAug 14, 2025
  If the Helion Motorized Toy Car suddenly stops while running, there might be a loss of throttle signal. Check the transmitter, receiver, and throttle wire connection. Alternatively, the low voltage cut-off or over-heat cut-off protection may have been activated. In this case, replace the battery pack or allow the ESC to cool down.
D
David EvansAug 17, 2025
Why doesn't my Helion conquest 10MT XB Motorized Toy Car motor work, but the ESC LED does?
- M
  michael36Aug 17, 2025
  If your Helion Motorized Toy Car doesn't work but the LED in the ESC is on, the connections between the motor and ESC may be broken. Check these connections and replace any defective connectors. Another possibility is that the motor itself is damaged, requiring replacement.
N
Nathan FreemanAug 21, 2025
How to fix Helion Motorized Toy Car not reaching top speed?
- L
  Lisa GarciaAug 21, 2025
  If the Helion Motorized Toy Car doesn't reach top speed and the red LED isn't solid at full throttle, some transmitter settings might be incorrect. Verify the settings, setting D/R, EPA, and ATL to 100% or their maximum values. Also, set TRIM to 0 or its neutral position.
E
Elizabeth DavisAug 25, 2025
What to do if Helion conquest 10MT XB only goes backward?
- Y
  yreidAug 25, 2025
  If your Helion Motorized Toy Car doesn't move forward but does move backward, the direction of the throttle channel is likely incorrect. Reset the throttle channel direction from “NOR” to “REV,” or from “REV” to “NOR.”
R
Randall NelsonAug 27, 2025
Why won't my Helion conquest 10MT XB Motorized Toy Car motor work after powering on?
- L
  Lisa FletcherAug 27, 2025
  If the Helion Motorized Toy Car motor can’t work, there's no sound, and the LED is off, the ESC might not be getting the correct voltage, or the connections between the battery pack and ESC could be broken. Check the battery wire connections and replace any defective connectors. The switch might also be damaged, requiring replacement.
A
aaron37Aug 31, 2025
Why does my Helion conquest 10MT XB Motorized Toy Car run backward when I give it throttle?
- B
  Brenda TateAug 31, 2025
  If your Helion Motorized Toy Car runs backward when you give it throttle, the wire connections between the ESC and the motor likely need to be changed. Swap two wire connections between the ESC and the motor.
R
Russell RobinsonSep 3, 2025
What to do if Helion conquest 10MT XB motor doesn’t work and the red LED blinks?
- R
  Renee RodriguezSep 3, 2025
  If the Helion Motorized Toy Car motor can’t work and the red LED blinks after powering on, the throttle signal may be abnormal. Check the throttle wire connection, ensuring it is plugged into the throttle channel of the receiver. Alternatively, automatic throttle range calibration may have failed. Set the “TRIM” of the throttle channel to 0 or turn the knob to its neutral position.
J
Jamie HaynesSep 6, 2025
Why can't my Helion Motorized Toy Car go backward?
- J
  John FlemingSep 6, 2025
  If the Helion Motorized Toy Car can't go backward, the jumper position might be wrong. Check the jumper and plug it into the correct position. Also, the neutral point of the throttle channel may have changed or drifted. Set the “TRIM” of the throttle channel to 0 or turn the knob to its neutral position.
G
gonzalezamySep 9, 2025
Why is my Helion Motorized Toy Car motor cogging when accelerating?
- D
  donnarobinsonSep 10, 2025
  If the Helion Motorized Toy Car motor is cogging when accelerated quickly, the battery may have limited discharge ability. Use a battery with better discharge ability. The motor RPM might also be too high, making the gear ratio too aggressive. Use a motor with lower RPM, or use a smaller pinion to get a softer gear ratio. There could also be a problem with components in the drivetrain, so check the car's driving system.