Hico Medical Systems HICO-VARIOTHERM 550 User Manual (English)

Questions and Answers:

C
carrie85Aug 21, 2025
What to do if Hico Medical Systems HICO-VARIOTHERM 550 has no or insufficient water circulation?
- M
  Mackenzie SchneiderAug 21, 2025
  If your Hico Medical Systems Medical Equipment exhibits no or insufficient water circulation, here are a few things you can check: * Ensure hoses or pads are not kinked and are correctly laid and positioned. * Make sure the couplings are fully engaged. * Verify the unit is at the same height or above the water pad. If the patient weight is high, position the unit higher than the water pad. * If there's intense foam formation, replace the water.
S
Shawn LamAug 22, 2025
What to do if Hico Medical Systems HICO-VARIOTHERM 550 shows "TEMP.DIFF. >1 °C" alarm?
- N
  Nathan PalmerAug 23, 2025
  If your Hico Medical Systems Medical Equipment displays the alarm message "TEMP.DIFF. >1 °C", it could be due to coupling or decoupling of the water pad during operation. Acknowledge the alarm by pressing the “Alarm OFF” button.
A
Ashley WallaceAug 25, 2025
Why does my Hico Medical Systems HICO-VARIOTHERM 550 display "TEMP.DIFF. >1 °C" every 10 minutes?
- C
  cameronjacksonAug 25, 2025
  If your Hico Medical Systems Medical Equipment shows the message "TEMP.DIFF. >1 °C" every 10 minutes, it may be due to intense foam formation in the tank. In this case, replace the water.
J
jason53Aug 26, 2025
What to do if couplings of Hico Medical Systems HICO-VARIOTHERM 550 are stiff?
- N
  nathanwiseAug 26, 2025
  If the couplings on your Hico Medical Systems Medical Equipment feel stiff, it's likely due to a dry and brittle sealing ring. Grease the sealing ring with vaseline, silicone grease, or a similar lubricant.
S
sparkschristineAug 27, 2025
What to do if coupling connection of Hico Medical Systems HICO-VARIOTHERM 550 Medical Equipment drips constantly?
- B
  Barbara FieldsAug 28, 2025
  If the coupling connection of your Hico Medical Systems Medical Equipment drips constantly, it's likely due to a damaged or missing exterior, visible sealing ring. Replace the sealing ring.
M
Matthew RichAug 29, 2025
What to do if coupling valve of the non-connected coupling drips constantly in Hico Medical Systems HICO-VARIOTHERM 550?
- G
  Gary JonesAug 29, 2025
  If the coupling valve of the non-connected coupling drips constantly, insert and loosen coupling several times.
P
Perry AdamsAug 31, 2025
What to do if Hico Medical Systems Medical Equipment shows alarm and display message: “CHECK UNIT” “->CUSTOMER SERVICE”?
- D
  Dr. Steven AndersonAug 31, 2025
  If your Hico Medical Systems Medical Equipment displays the alarm message “CHECK UNIT” “->CUSTOMER SERVICE”, it could be due to various defects, an empty water tank, a sensor break/short circuit T1, or a sensor short circuit T2. Refill with water if the water tank is empty. For other defects and sensor issues, further assistance is needed.
J
Juan HammondSep 1, 2025
What to do if Hico Medical Systems Medical Equipment displays alarm and display message: “Water level!?”?
- J
  Jeremiah WilliamsSep 1, 2025
  If your Hico Medical Systems Medical Equipment shows the alarm message “Water level!?”, which can be acknowledged for 10 minutes, it may be due to the water level being too low, the unit not being completely horizontal, or a sensor deviation. Refill the water if the level is low, and ensure the unit is positioned horizontally. For sensor deviation issues, further assistance is needed.
J
jhicksSep 3, 2025
Why is there no or insufficient water circulation in my Hico Medical Systems Medical Equipment?
- C
  Clayton BarnesSep 3, 2025
  There may be no or insufficient water circulation in your Hico Medical Systems Medical Equipment because the hoses or pads are kinked or folded, connections are not tight, the unit is positioned too far below the water pad, there is strong foam formation, high patient weight, or the pump is worn or defective. Here are some things to check: * Ensure hoses and pads are correctly placed and positioned. * Insert hose connections firmly into each other. * Position the unit at the same height or higher than the water pad. * Change the water if there is strong foam formation. * Position the unit higher than the water pad.
J
Jordan LambSep 5, 2025
What to do if Hico Medical Systems Medical Equipment displays alarm and display message every 10 min.: “TEMP.DIFF. > 1°C”?
- D
  Deanna Gill MDSep 5, 2025
  If your Hico Medical Systems Medical Equipment displays the alarm message “TEMP.DIFF. > 1°C” every 10 minutes, it may be due to insufficient cooling output, defective cooling elements or pump, strong foam formation in the tank or interrupted bypass. Change the water if there is strong foam formation in the tank.

Hico Medical Systems HICO-VARIOTHERM 550 Specifications

General

Brand	Hico Medical Systems
Model	HICO-VARIOTHERM 550
Category	Medical Equipment
Language	English

Hico Medical Systems HICO-VARIOTHERM 550 User Manual

Table of Contents

Questions and Answers:

Hico Medical Systems HICO-VARIOTHERM 550 Specifications