HID Signo 25B - Page 2

15
Equipment
8T2 9
ACC Control READER
General Signaling
Equipment
E4662
ABCD12345678
© 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved.
PLT-04026, Rev. B.3
Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com
hidglobal.com
CIDF18000157
Optional features
Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA /
Source -1 mA.
Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of
5 VDC when the reader is removed from its backplate.
Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires
(common, normally open, and normally closed).
Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires.
Configuration options are available within HID Biometric Manager™.
Specications
Input Voltage (V DC)
12V DC
Standby Current AVG
1
800 mA
Max Current AVG
2
1.5 A
Peak Current
3
2 A
Operating Temperature
-4° F to 150° F (-20° C to 66° C)
1
Standby AVG - Root Mean Square current draw without a card in the RF eld.
2
Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL.
3
Peak - highest instantaneous current draw during RF communication.
Regulatory
UL
Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be
used with listed (UL294) control equipment. Suitable for outdoor use.
Only Wiegand and Bluetooth communications have been evaluated by UL.
The Open Collector Output has not been evaluated by UL.
RS485 communications has not been evaluated by UL.
Inputs (reserved for future use) have not been evaluated by UL.
The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel.
The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using
mobile devices with BLE version 4.2 and later listed at:
https://www.hidglobal.com/mobile-access-compatible-devices
Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities
having jurisdiction. Follow all National and Local Codes.
UL 294 Performance Levels
Model #
Access Control
Line Security Level
Destructive
Attack Level
Endurance
Level
Stand-By
Power Level
Conditions
25B Level I Level I Level IV Level I
CE Marking
HID Global hereby declares that these proximity readers are in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales
y otras disposiciones relevantes de la Directiva 2014/53/EU.
HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles
et aux autres stipulations pertinentes de la Directive 2014/53/EU.
A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as
exigências essenciais e outras condições da diretiva 2014/53/EU.
HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten
Bestimmungen der Richtlinie 2014/53/EU erfüllen.
HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti
come previsto dalla Direttiva europea 2014/53/EU.
Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at:
http://www.hidglobal.com/certifications
Russia
Дата изготовления указана на маркировке оборудования
Представитель в Российской Федерации
Название
ООО «Дофин»
Адрес
140573, РФ, Московская обл., Озерский район, с. Бояркино
Контактное лицо
Л.Н. Голубова
Телефон
+7 495 223 6008
e-mail
local.declarant@gmail.com
Israel
השימוש במכשיר הינו על בסיס ״משני״ ופטור מרשיון הפעלה אלחוטי.
רק ״בפעולת בזק״ לשימוש עצמי של הלקוח בלבד, הלקוח פטור מרשיון הפעלה אלחוטי.
אסור להחליף את האנטנה המקורית של המכשיר, ולא לעשות בו כל שינוי טכני אחר.
Canada Radio Certification
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Taiwan
根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Korean KCC
25B
항목
규격
송신주파수
RFID:13.56MHz
수신주파수
RFID:13.56MHz
출력
RFID:10m에서47.544mv이하
전원
DC12.0V
전파형식
A1D
발진방식
X-tal
변조방식
RFID:ASK,NFC:GFSK
Singapore UAE Australia and New Zealand
Complies with
IMDA Standards
DA103548
TRA
REGISTERED NO:
ER72356/19
DEALER NO:
DA37204/14
E4662
South Africa
TA-2019/920
APPROVED
Brazil
Compliance Statement
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela
Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site
da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it
complies with the applicable technical requirements. For more information, consult ANATEL website - www.
anatel.gov.br
RF Warning Statement
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a
visible location:
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.
This equipment operates in secondary character, meaning it does not have the right of protection against
harmful interference, even against those the same character, and it cannot cause any interference to
systems operating in the primary character.
15
Equipment
8T2 9
ACC Control READER
General Signaling
Equipment
E4662
ABCD12345678
© 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved.
PLT-04026, Rev. B.3
Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com
hidglobal.com
CIDF18000157
Optional features
Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA /
Source -1 mA.
Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of
5 VDC when the reader is removed from its backplate.
Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires
(common, normally open, and normally closed).
Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires.
Configuration options are available within HID Biometric Manager™.
Specications
Input Voltage (V DC)
12V DC
Standby Current AVG
1
800 mA
Max Current AVG
2
1.5 A
Peak Current
3
2 A
Operating Temperature
-4° F to 150° F (-20° C to 66° C)
1
Standby AVG - Root Mean Square current draw without a card in the RF eld.
2
Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL.
3
Peak - highest instantaneous current draw during RF communication.
Regulatory
UL
Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be
used with listed (UL294) control equipment. Suitable for outdoor use.
Only Wiegand and Bluetooth communications have been evaluated by UL.
The Open Collector Output has not been evaluated by UL.
RS485 communications has not been evaluated by UL.
Inputs (reserved for future use) have not been evaluated by UL.
The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel.
The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using
mobile devices with BLE version 4.2 and later listed at:
https://www.hidglobal.com/mobile-access-compatible-devices
Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities
having jurisdiction. Follow all National and Local Codes.
UL 294 Performance Levels
Model #
Access Control
Line Security Level
Destructive
Attack Level
Endurance
Level
Stand-By
Power Level
Conditions
25B Level I Level I Level IV Level I
CE Marking
HID Global hereby declares that these proximity readers are in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales
y otras disposiciones relevantes de la Directiva 2014/53/EU.
HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles
et aux autres stipulations pertinentes de la Directive 2014/53/EU.
A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as
exigências essenciais e outras condições da diretiva 2014/53/EU.
HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten
Bestimmungen der Richtlinie 2014/53/EU erfüllen.
HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti
come previsto dalla Direttiva europea 2014/53/EU.
Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at:
http://www.hidglobal.com/certifications
Russia
Дата изготовления указана на маркировке оборудования
Представитель в Российской Федерации
Название
ООО «Дофин»
Адрес
140573, РФ, Московская обл., Озерский район, с. Бояркино
Контактное лицо
Л.Н. Голубова
Телефон
+7 495 223 6008
e-mail
local.declarant@gmail.com
Israel
השימוש במכשיר הינו על בסיס ״משני״ ופטור מרשיון הפעלה אלחוטי.
רק ״בפעולת בזק״ לשימוש עצמי של הלקוח בלבד, הלקוח פטור מרשיון הפעלה אלחוטי.
אסור להחליף את האנטנה המקורית של המכשיר, ולא לעשות בו כל שינוי טכני אחר.
Canada Radio Certification
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Taiwan
根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Korean KCC
25B
항목
규격
송신주파수
RFID:13.56MHz
수신주파수
RFID:13.56MHz
출력
RFID:10m에서47.544mv이하
전원
DC12.0V
전파형식
A1D
발진방식
X-tal
변조방식
RFID:ASK,NFC:GFSK
Singapore UAE Australia and New Zealand
Complies with
IMDA Standards
DA103548
TRA
REGISTERED NO:
ER72356/19
DEALER NO:
DA37204/14
E4662
South Africa
TA-2019/920
APPROVED
Brazil
Compliance Statement
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela
Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site
da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it
complies with the applicable technical requirements. For more information, consult ANATEL website - www.
anatel.gov.br
RF Warning Statement
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a
visible location:
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.
This equipment operates in secondary character, meaning it does not have the right of protection against
harmful interference, even against those the same character, and it cannot cause any interference to
systems operating in the primary character.