Need help?Do you have a question about the HIKVISION DS-7332HQI-K4 and is the answer not in the manual?
General| Product color | Black |
|---|---|
| USB connectivity | Yes |
| Channels quantity | 32 channels |
| Total storage capacity | 10000 GB |
| Maximum video resolution | 3840 x 2160 pixels |
| Video compression formats | H.264, H.264+, H.265, H.265+ |
| Analog signal format system | NTSC, PAL |
| Playback resolutions supported | 4K (3840 x 2160)/30Hz, 2K (2560 x 1440)/60Hz, 1920 x 1080/60Hz, 1280 x 1024/60Hz, 1280 x 720/60Hz, 1024 x 768/60Hz |
| RS-485 ports | 1 |
| USB 2.0 ports quantity | 2 |
| Number of users | 128 user(s) |
| Ethernet interface type | Gigabit Ethernet |
| Supported network protocols | TCP / IP, PPPoE, DHCP, Hik-Connect, DNS, DDNS, NTP, SADP, NFS, iSCSI, UPnPTM, HTTPS, ONVIF |
| Power requirements | 100 - 240 VAC |
| Power consumption (typical) | 45 W |
| HDD interface | Serial ATA |
| Maximum HDD capacity | 8000 GB |
| Number of HDDs supported | 4 |
| Operating temperature (T-T) | -10 - 55 °C |
| Operating relative humidity (H-H) | 10 - 90 % |
Weight and Dimensions| Depth | 390 mm |
|---|---|
| Width | 440 mm |
| Height | 70 mm |
| Weight | 7000 g |
HDMI/VGA output, multi-channel live view, and display options.
HDD capacity, network disk connections, and recording time.
Exporting data to USB/eSATA, managing backup devices.
Alarm configuration, system exceptions, and response actions.
Description of rear panel connectors and ports.
Procedures for powering the DVR on and off safely.
Initial setup for the DVR, including setting an admin password.
Configuring and using a graphical unlock pattern for device access.
Process of logging into the DVR using user credentials.
Adding network cameras to the DVR connection list.
Initial activation and setup for IP cameras before adding them.
Adding network cameras to the DVR connection list.
Modifying settings for already connected IP cameras.
Setting analog and IP signal input types and enabling 5 MP transmission.
Various functions available in live view mode.
Setting up PTZ parameters for camera control.
Configuring camera positions, patrol paths, and movement patterns.
Interface for direct manual control of PTZ cameras.
Setting video compression, resolution, and bitrate for recording.
Setting up scheduled recording times for cameras.
Setting up motion detection areas, sensitivity, and triggers.
Configuring recording based on VCA events like face/line detection.
Methods to protect recorded files from overwriting.
Searching and playing back recordings by selecting a specific channel.
Searching and playing back recordings based on a specific date and time.
Searching recordings based on event types like motion or alarms.
Efficiently reviewing video by skipping non-relevant segments.
Backing up video and picture files via normal search.
Backing up event-related recordings using event search.
Setting up motion detection areas, sensitivity, and triggers.
Configuring handling methods for external sensor alarms.
Detecting video loss and setting alarm response actions.
Detecting video tampering and setting alarm response actions.
Configuring actions taken when an alarm or exception occurs.
Configuring face detection rules, sensitivity, and linkage actions.
Configuring vehicle detection for traffic monitoring and license plate capture.
Configuring rules for detecting objects crossing a virtual line.
Configuring rules for detecting objects entering a defined virtual region.
Detecting objects entering a predefined virtual region.
Detecting objects exiting a predefined virtual region.
Setting up basic network parameters like IP address and working mode.
Configuring advanced network features and protocols.
Enabling remote access and management via the Hik-Connect service.
Setting up RAID arrays for data redundancy and storage.
Restoring degraded RAID arrays using hot spare disks or manual rebuilding.
Preparing newly installed hard drives for use by the DVR.
Adjusting image and camera parameters for optimal video quality.
Setting camera-specific parameters like signal switch, defog, and WDR.
Updating the DVR firmware via local backup or FTP server.
Adding, deleting, and managing user accounts and permissions.
Solutions for common issues like no image, beeps, or video output problems.
To Next Page
