Home
HIKVISION
Control Unit
DS-PM1-D
HIKVISION DS-PM1-D User Manual
4
of 1
of 1 rating
142 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
69
2. Select the
Alarm Receiver Center
as
1
or
2
for configuration, and slide the slider to enable the
selected alarm receiver center.
Note
Only if the alarm receiver center 1 is enabled, you can set the alarm receiver center 2 as the
backup channel
and edit the channel parameters.
3. Select the
Protocol Type
as
ADM-CID
,
ISUP
,
SIA-DCS
,
*SIA-DCS
,
*ADM-CID, CSV-IP,
or
FSK
Module
to set uploading mode.
69
71
Table of Contents
Default Chapter
7
Table of Contents
7
Chapter 1 Introduction
10
System Description
10
Chapter 2 Start up
13
Authority Management
13
Initial the Device with HPC
14
Connect to the Network
14
Create a Site
14
Add Device
14
Initial the Device with HC
14
Connect to the Network
15
Download and Login the Mobile Client
15
Add Device
15
Chapter 3 User Management
16
User Management
16
Invite the Administrator
16
Cancel Installer Access
17
Add an Operator
18
Delete an Operator
19
Disable the Hik-Connect Service
20
Invite the Installer
20
Access Entries
20
Chapter 4 Configuration
22
Set-Up with Hik-Proconnect
22
Use the Hik-Proconnect APP
22
Use the Hik-Proconnect Portal
40
Set-Up with Hik-Connect
43
Set-Up with the Web Client
64
Communication Settings
65
Device Management
80
Area Settings
90
Video Management
90
Permission Management
92
Maintenance
94
System Settings
98
Check Status
110
Report to ARC (Alarm Receiver Center)
111
Setup ATS in Transceiver of Receiving Center
111
Setup ATS in Transceiver of the Panel
112
Signaling Test
113
Chapter 5 General Operations
115
Arming
115
Disarming
116
SMS Control
116
Trouble Shooting
117
Communication Fault
117
IP Conflict
117
Web Page Is Not Accessible
117
Hik-Connect Is Offline
117
Network Camera Drops off Frequently
117
Failed to Add Device on APP
117
Alarm Information Is Not Reported to App/4200/Alarm Center
118
Mutual Exclusion of Functions
118
Unable to Enter Registration Mode
118
Zone Fault
118
Zone Is Offline
118
Zone Tamper-Proof
118
Zone Triggered/Fault
118
Problems While Arming
119
Failure in Arming (When the Arming Process Is Not Started)
119
Operational Failure
119
Failed to Enter the Test Mode
119
The Alarm Clearing Operation on the Panel Does Not Produce the Alarm Clearing Report
119
Mail Delivery Failure
119
Failed to Send Test Mail
119
Failed to Send Mail During Use
120
Failed to Send Mails to Gmail
120
Failed to Send Mails to QQ or Foxmail
120
Failed to Send Mails to Yahoo
120
Mail Configuration
121
Input Types
122
Output Types
125
Event Types
126
Access Levels
127
Signalling
129
Detection of ATP/ATS Faults
129
ATS Category
129
SIA and CID Code
130
Communication Matrix and Operation Command
141
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the HIKVISION DS-PM1-D and is the answer not in the manual?
Ask a question
HIKVISION DS-PM1-D Specifications
General
Brand
HIKVISION
Model
DS-PM1-D
Category
Control Unit
Language
English
Related product manuals
HIKVISION DS-K2M061
17 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
