Hitachi AP1 - Page 87

--------------------------------------------------------HMCS46C,HMCS46CL
• ELECTRICAL CHARACTERISTICS-1 (Vee = SV ± 10%, Ta = _20°C to +7SoCI
Item
Symbol
Test Conditions
Value
min. typo
Input "Low" Voltage
V
IL
-
-
Input "High" Voltage (11
V
IHl
Vee - 1.0
-
Input "High" Voltage (21
V
IH2
Vee - 1.0
-
Output "Low" Voltage
VOL
IOL = 1.6mA
-
-
Output "High" Voltage (1)
V
OHl
-IOH
= 1.0mA
2.4
-
Output "High" Voltage (2)
V
OH2
-loH = 0.01mA
Vee - 0.3
-
Interrupt Input Hold Time
tiNT
20Tinst
-
Interrupt Input Fall Time
tflNT
-
-
Interrupt Input Rise Time
trlNT
-
-
Output "High" Current
IOH
V
OH
= 10V
-
-
Input Leakage Current
V
in
= Oto Vee
-
-
IlL
V
in
= 0 to 10V
-
-
Pull up MOS Current -Ip
Vee = 5V
60
-
V
in
= Vee, Vee = 5V,
Supply Current (1)
leel
Ceramic Filter
-
-
Oscillation,
(fasc = 800kHz)
V
in
= Vee, Vee = 5V
R
t
Oscillation,
Supply Current (2)
lee2
(fasc = 800kHz)
-
-
External Clock
Operation (fcp = 800kHz)
Standby I/O Leakage
HLT
I V in = 0 to Vee
-
-
Current
I
LS
= 1.0V
I V in = 0 to 10V
-
-
Standby Supply Current
Ices
V
in
=V
ee
, HLT = 0.2V
- -
External Clock Operation
External Clock Frequency
fcp
350
-
External Clock Duty Duty
45
50
External Clock Rise Time
t
rcp
0
-
External Clock Fall Time
ttcp
0
-
Instruction Cycle Time
T
inst
T
inst
= 4/fcp
4.7
-
Internal Clock Operation (R
t
Oscillation)
Clock Oscillation Frequency
R
t
= 51kU ± 2%
Clock Oscillation Frequency
Ceramic Filter Circuit
Instruction Cycle Time
T
inst
= 4/fasc
[NOTE 11 All voltages are with respect to GND.
[NOTE 21 This is applied to RESET, HLT, OSC" INTo, INT, and the with Pull up MOSorCMOStype of I/O pins.
[NOTE 31 This is applied to the Open Drain type of I/O pins.
[NOTE 41 This is applied to the CMOS type of I/O pins.
[NOTE 51 This is applied to the with Pull up MOS or CMOS type of I/O pins.
[NOTE 61 This is applied to the Open Drain type of I/O pins.
[NOTE
71 I/O current is excluded.
[NOTE 81 The Standby I/O Leakage Current is the I/O leakage current in the Halt and Disable State.
[NOTE 91 I/O current is excluded.
Unit
Note
max.
1.0 V
Vee
V
2
10 V
3
0.8 V
-
V 4
-
V
5
-
p.s
50
p.s
50 p.s
3
p.A
6
1
2
3
p.A
3
250
p.A
2.0 mA
0.85
mA
7
1
p.A 5,8
3
p.A 6,8
12 p.A
9
850
kHz
55 %
0.2 p.s
0.2
p.s
11.4 p.s
The Standby Supply Current is the supply current at Vee = 5V ± 10% in the Halt State. The supply current in the case where the
supply voltage
falls to the Halt Duration voltage is called the Halt Current (lOHl. and it is shown in"ELECTRICAL CHARACTERISTICS -2."
85