What causes excessively low pressure difference in my Hitachi Air Conditioner?
Excessively low pressure difference in your Hitachi Air Conditioner is caused when the pressure ratio calculated from high pressure (Pd) and low pressure (Ps) is lower than 1.8 MPa during 3 minutes.
Why does my Hitachi RAS-5HRNME-AF show a power phase detection abnormality?
A power phase detection abnormality in Hitachi Air Conditioner indoor units can be caused by an open phase in the power source wiring.
What causes suction pressure decrease prevention to activate in my Hitachi Air Conditioner?
Activation of suction pressure decrease prevention in your Hitachi Air Conditioner can be caused by a shortage or leakage of refrigerant, piping clogging, a close-locked expansion valve, or a locked fan motor.
What causes heating overload in my Hitachi RAS-5HRNME-AF Air Conditioner?
Heating overload in your Hitachi Air Conditioner can be caused by outdoor heat exchanger clogging or short circuit, or an expansion valve close-locked.
What causes failure of refrigerant evaporation temperature thermistor in my Hitachi RAS-5HRNME-AF?
Failure of the refrigerant evaporation temperature thermistor in your Hitachi Air Conditioner is caused if the refrigerant evaporation temperature thermistor is short-circuited or cut.
What causes failure of suction gas pressure sensor in my Hitachi RAS-5HRNME-AF Air Conditioner?
Failure of the suction gas pressure sensor in your Hitachi Air Conditioner is caused if the low pressure sensor is short-circuited or cut.
What causes Opentherm communication failure in my Hitachi RAS-5HRNME-AF?
Opentherm communication failure in your Hitachi Air Conditioner is caused if there is no Opentherm communication for a continuous period of 1 minute.
What causes RF communication failure in my Hitachi Air Conditioner?
RF communication failure in your Hitachi Air Conditioner happens when there is no communication for 1 hour with one or two RF receivers which are bound to the RF-Bridge.
What causes transmission error between central and indoor communication in my Hitachi Air Conditioner?
A transmission error between central and indoor communication in your Hitachi Air Conditioner can be caused by an indoor fuse meltdown, or indoor/central connection wiring issues (breaking, wiring error, etc.).
What causes inverter fin temperature abnormality in my Hitachi RAS-5HRNME-AF?
An inverter fin temperature abnormality in your Hitachi Air Conditioner can be caused by a fin thermistor abnormality, heat exchanger clogging, or fan motor abnormality.
General| Brand | Hitachi |
|---|---|
| Model | RAS-5HRNME-AF |
| Category | Air Conditioner |
| Language | English |
Essential guidelines for safe operation, installation, and product lifecycle management.
Details maximum system pressure and cut-out settings for safe operation.
Essential checks and warnings required before starting the system.
Manages compressor protection, defrosting, and airflow for optimal system performance.
Guides users on identifying and resolving common operational problems and abnormal sounds.
Provides a diagram and list of parts for the outdoor unit.
Illustrates the refrigerant flow and identifies key components in the cycle.
Important safety and installation guidelines for the outdoor unit.
Specifies clearance for single outdoor unit installations.
Specifies clearance for multiple outdoor unit installations.
Details space requirements for blocked outlet or lateral sides.
Specifies space for stacked and multi-row outdoor unit installations.
Guidelines for preparing a stable and suitable concrete foundation.
Instructions for mounting the unit and installing in windy conditions.
Methods for supporting refrigerant piping to prevent damage.
Procedures for connecting refrigerant piping to the outdoor unit.
Guidance on installing piping covers and handling stop valves.
Charts for designing refrigerant piping length based on height difference.
Specifies the correct pipe sizes for gas and liquid lines.
Safety guidelines and procedures for pipe brazing work.
Details the factory refrigerant charge amounts for different models.
Steps for collecting refrigerant into the outdoor unit during relocation.
Instructions for connecting the drain pipe using the boss.
General checks for electrical components, compliance, and power supply.
Diagrams for connecting electrical wiring to outdoor units.
Guide to setting DIP switches for various functions and configurations.
General guidelines for wiring, including noise protection and compliance.
Wiring diagrams and guidelines for connecting indoor and outdoor units.
Specifies minimum wire sizes for power and control connections.
Essential pre-run checks for the unit, electrical system, and refrigerant circuit.
Step-by-step guide for performing the test run using the indoor unit controls.
Instructions for initiating and managing test runs via outdoor unit DIP switches.
Details high pressure switch and fuse settings for compressor safety.
Explains how thermistor temperature affects fan motor output.
Lists alarm codes, their origins, details, and main causes.
Provides in-depth information on troubleshooting specific alarm codes and abnormalities.
Addresses issues related to pressure differences, gas temperature, and sensor failures.
To Next Page
