To Next PageTo Next PageWhy am I getting a transmission error on my Hitachi RPC-4.0FSN3E?
A transmission error in your Hitachi Air Conditioner could be due to a melted outdoor fuse or issues with the indoor/outdoor connection wiring, such as breaks or wiring errors.
Why does my Hitachi RPC-4.0FSN3E show an error related to incorrect outdoor and indoor unit settings?
An incorrect setting of outdoor and indoor units on your Hitachi Air Conditioner may be caused by an outdoor/indoor unit capacity setting error or if the indoor total capacity is excessively large or small.
What does it mean when the compressor protection alarm on my Hitachi RPC-4.0FSN3E Air Conditioner cannot be reset?
A compressor protection alarm on your Hitachi Air Conditioner that cannot be reset from the remote controller indicates that alarm codes 02, 07, 08, 39, 43 to 45, or 47 have been triggered three times within six hours.
What causes an indoor unit number setting error on my Hitachi RPC-4.0FSN3E?
An indoor unit number setting error on your Hitachi Air Conditioner occurs when indoor units with the same number exist in a refrigerant piping system.
What causes the indoor RA fan protection device to activate on my Hitachi KP Air Conditioner?
The indoor RA fan protection device on your Hitachi KP Air Conditioner may activate due to fan motor overheating or locking.
What causes the indoor OA fan protection device to activate on my Hitachi KPI or DX-KIT2 Fan Air Conditioner?
The indoor OA fan protection device on your Hitachi KPI or DX-KIT2 Fan Air Conditioner might activate because of fan motor overheating or locking.
What does abnormal transmission between PCB1 and PCB2 mean for my Hitachi RPC-4.0FSN3E Air Conditioner?
Abnormal transmission between PCB1 and PCB2 in your Hitachi Air Conditioner can be caused by loose or disconnected connections.
What would cause a problem with the air inlet thermistor on my Hitachi KPI Air Conditioner?
A problem with the air inlet thermistor (RA for KPI) in your Hitachi Air Conditioner could be due to a loose, disconnected, broken, or short-circuited connector.
What would cause a problem with the air outlet thermistor on my Hitachi KPI Air Conditioner?
A problem with the air outlet thermistor (OA for KPI) in your Hitachi Air Conditioner could be due to a loose, disconnected, broken, or short-circuited connector.
What would cause a problem with the liquid pipe thermistor on my Hitachi Air Conditioner?
A problem with the liquid pipe thermistor in your Hitachi Air Conditioner could be due to a loose, disconnected, broken, or short-circuited connector.
General| Brand | Hitachi |
|---|---|
| Model | RPC-4.0FSN3E |
| Category | Air Conditioner |
| Language | English |
General safety information and specific symbols used in the manual.
Further safety advice regarding electrical hazards and system usage.
Information on pressure vessels and high pressure switches for safety.
Conditions for outdoor unit placement regarding sunlight, ventilation, and access.
Required clearances around the unit for installation and maintenance.
Installation guidelines based on surrounding walls.
Instructions on selecting pipe sizes for outdoor units and branch connections.
Details on copper pipe specifications, connection methods, and insulation.
Information on pipe connection kits for FSXN1E series.
Pipe size specifications for FSXN1E series with 3 pipes.
Guidelines on outdoor unit installation, pipe arrangement, and connection.
Instructions for installing refrigerant pipes, including flared connections and insulation.
Connection details for heat pump and heat recovery systems piping.
Procedure for performing air-tight tests on refrigerant circuits.
Steps for vacuum pumping the system to remove moisture and air.
Method for calculating and recording additional refrigerant needed based on piping.
Procedure for charging additional refrigerant into the system.
General precautions and safety advice for electrical wiring work.
Instructions for connecting electrical wiring to the outdoor unit.
Pre-test checks for refrigerant pipes, communication cables, and settings.
Checklist for verifying system operation during the test run.
List of common alarm codes, categories, contents, and possible causes.
Details on devices protecting the compressor, like pressure switches and oil heaters.
