homelabs HME010019N - User Manual

Questions and Answers

D
Dana HernandezAug 5, 2025
How to clean mold from homelabs HME010019N?
- N
  nathanielsmithAug 5, 2025
  If you notice mold or residue in your homelabs Ice Maker, power it off and clean it thoroughly. Use room temperature water and mild detergent with a soft cloth to clean all inside surfaces, then rinse with water. Run 3 cycles of ice making with new water each time, discarding the ice. For best results, use professional ice machine descaler and sanitizer solutions, following the manufacturer’s instructions. Keeping the water, scoop, ice machine, and surrounding area clean can help prevent mold.
K
Kaitlyn HudsonAug 10, 2025
Why is my homelabs Ice Maker making cycle normal but no ice is being formed?
- J
  Jessica FitzgeraldAug 10, 2025
  If your homelabs Ice Maker's ice making cycle seems normal, but no ice is forming, it could be due to a few reasons. The room temperature might be too high (it should be between 50°F and 105°F or 10°C and 40°C), or the water temperature in the inner tank could be too high (it should be between 40°F and 90°F or 4°C and 32°C). If the temperature is within range, contact hOmeLabs Customer Service at 1-(800)-898-3002.
J
jacquelinechristianAug 15, 2025
What to do if the FULL indicator is on my homelabs Ice Maker?
- M
  Mrs. Victoria RodriguezAug 15, 2025
  If the FULL indicator is on for your homelabs Ice Maker, it means the ice basket is full. Remove the ice from the basket. If you want the appliance to continue making ice even with the FULL indicator on, you can continuously hold the “SELECT SIZE” button for 5 seconds. This will allow the appliance to run 10 additional cycles.
S
shelbyeverettAug 20, 2025
Why are ice cubes sticking together in my homelabs Ice Maker?
- M
  Molly ChavezAug 21, 2025
  If the ice cubes in your homelabs Ice Maker are sticking together, it could be because the ice making cycle is too long or the water temperature in the inner tank is too low. Stop the appliance by pressing the “ON/O button, and restart it when the ice blocks melt. Select the small size ice cube select Replace the water. Ensure the water temperature is between 40°F–90°F (4°C–32°C).
A
Alexandra HillAug 26, 2025
What to do if the WATER shortage indicator is on in my homelabs Ice Maker?
- M
  melissa66Aug 26, 2025
  If the WATER shortage indicator is on for your homelabs Ice Maker, it means the appliance lacks water. Stop the appliance by pressing the “ON/ OFF” button. Fill the tank with water, and press the “ON/OFF” button again to restart the appliance.
M
Mr. Gary ThorntonAug 30, 2025
Why is my homelabs HME010019N Ice Maker leaking water?
- T
  Thomas SmithAug 30, 2025
  If you notice water leaking from your homelabs Ice Maker, make sure the Water Drain Cap (located at the front bottom of the unit) is securely in place.

Summary

Important Safeguards

General Safety Instructions

Covers primary safety rules, warnings, and general operational precautions for safe use of the ice maker.

Specific Hazard Warnings

Details dangers related to flammable refrigerants, improper servicing, and product disposal.

Installation and Electrical Safety

Provides guidelines for proper installation, wiring color codes, and electrical safety measures.

Getting to Know Your Ice Maker

Parts Overview

Identifies and describes all the physical components and parts of the ice maker.

Control Panel Explained

Details the functionality of the control panel buttons and indicator lights.

Operating Procedures & Maintenance

Initial Setup and Power Requirements

Guides first-time users through initial setup, unpacking, cleaning, and electrical connection requirements.

Ice Making Process

Explains the step-by-step process for making ice, including water filling and size selection.

Cleaning and Maintenance

Outlines essential procedures for cleaning the ice maker's interior, exterior, and accessories.

Troubleshooting Guide

Common Issues and Solutions

Provides a table of common problems, their possible causes, and recommended solutions.

Product Information and Support

Warranty Details

Explains the terms, conditions, exclusions, and claim process for the product's limited warranty.

Manufacturing and Contact Information

Lists product specifications, warnings, and available customer support contact methods.

homelabs HME010019N Specifications

General

Ice Production	26 lbs per day
Ice Shape	Bullet
Water Tank Capacity	2.2 liters
Cycle Time	6-8 minutes
Product Type	Countertop Ice Maker
Ice Storage Capacity	1.5 lbs
Voltage	115V/60Hz
Material	Plastic
Ice Size	Small
Power Consumption	120W

Related product manuals

homelabs Nugget

9 pages