To Next PageTo Next PageWhat to do if grass wraps around drive shaft housing and string head of Homelite 26SS UT22650?
If grass is wrapping around the drive shaft housing and string head of your Homelite Trimmers, it is likely caused by: * Cutting tall grass at ground level: Cut tall grass from the top down to prevent wrapping. * Operating trimmer at part throttle: Operate the trimmer at full throttle.
Why Homelite 26SS UT22650 string will not advance?
If the string on your Homelite Trimmers isn't advancing, consider these potential causes and solutions: * String welded to itself: Lubricate with silicone spray. * Not enough string on spool: Install more string. * String worn too short: Pull strings while alternately pressing down on and releasing spool retainer. * String tangled on spool: Remove string from spool and rewind. * Engine speed too slow: Advance string at full throttle.
What to do if Homelite Trimmers spool retainer hard to turn?
If the spool retainer on your Homelite Trimmers is hard to turn, it's likely because the screw threads are dirty or damaged. Clean the threads and lubricate them with grease. If this doesn't improve the situation, replace the spool retainer.
What to do if Homelite 26SS UT22650 Trimmers engine does not reach full speed and emits excessive smoke?
If your Homelite Trimmers engine isn't reaching full speed and is emitting excessive smoke, the causes and solutions are: * Check the lubricant fuel mixture. Use fresh fuel and the correct 2-cycle lubricant mix. * The air filter may be dirty. Clean the air filter. * The carburetor may be out of adjustment, in this case you should contact an authorized servicing dealer.
Why Homelite 26SS UT22650 Trimmers lubricant drips from muffler?
If lubricant is dripping from the muffler of your Homelite Trimmers, it could be due to: * Operating the trimmer at part throttle: Operate the trimmer at full throttle. * Incorrect lubricant/fuel mixture: Use fresh fuel and the correct 2-cycle lubricant mix. * Dirty air filter screen: Clean the air filter.
Why Homelite 26SS UT22650 engine starts but will not accelerate?
If your Homelite Trimmers engine starts but won't accelerate, it might need to warm up for about three minutes. If it still doesn't accelerate after warming up, contact a servicing dealer.
Why Homelite Trimmers engine starts but will only run at high speed at half choke?
If your Homelite Trimmers engine starts but only runs at high speed at half choke, the carburetor likely requires adjustment. Contact an authorized servicing dealer to resolve this issue.
Why Homelite Trimmers engine starts, runs, and accelerates but will not idle?
If your Homelite Trimmers engine starts, runs, and accelerates but won't idle, the idle speed screw on the carburetor likely needs adjustment. Turn the idle speed screw clockwise to increase the idle speed.
General| Engine Type | 2-Cycle |
|---|---|
| Displacement | 26 cc |
| Starting System | Recoil |
| Shaft Type | Straight |
| Cutting Width | 43 cm |
| Fuel Capacity | 0.5 L |
| Line Diameter | 0.095 inches |
| Fuel Tank Capacity | 14 fl. oz. |
| Drive Type | Flex Shaft |
Overview of Homelite 26cc string trimmers, highlighting design for safety, performance, and dependability.
User must read and understand the manual before using the product to reduce injury risk.
Identifies main parts of the 26CS and 26SS string trimmers with labels A through M.
Details components A-D for the front handle assembly of the string trimmer.
Illustrates parts A-E for the string head assembly and part A for pull strings.
Lists components A-E for the grass deflector and bracket assembly.
Identifies parts A-I for the grass deflector and drive shaft housing.
Shows stop switch, primer bulb, throttle trigger, starter handle, and choke positions.
Demonstrates proper operating position and highlights safe vs. dangerous cutting zones.
Illustrates spool retainer and the path of the trimmer line through the eyelet.
Shows spool and eyelets, illustrating how to wind string.
Demonstrates how to pull strings for line advance.
Details latch, filter cover, and idle speed screw for maintenance and adjustments.
