HomeSeer HS-LS100+ - User Manual

HS-LS100+ Z-Wave Leak Sensor
OVERVIEW HS-LS100+ is a compact, easy to install leak sensor. It is designed to control other Z-Wave devices directly
or it may be used with a variety of Z-Wave certified home controllers to launch automation events or scenes.
Applications
• Use to activate Z-Wave devices such as sirens or water valve controllers when a leak is sensed.
• Use to trigger home automation events (aka “scenes”, “automations” or “robots”) when a leak is sensed.
Configuration
HS-LS100+ is battery powered and includes a Z-Wave network button, LED indicator and a magnetic wall
mount/wired probe assembly. The unit may be deployed as a free-standing sensor (using built-in probes) or as a
wired remote sensor (via the wall mount/wired probe assembly).
Z-Wave Network Installation Remove the back cover by rotating counter-clockwise and install 1 ER14250 battery
(included) inside HS-LS100+. Include the sensor into your Z-Wave network using the instructions below. Then,
replace the back cover. Use the instructions below to include or exclude HS-LS100+ to/from your Z-Wave network.
Inclusion (recommended if your home controller supports “S0” or “S2” Z-Wave encryption)
1. Put your home controller into Z-Wave ‘inclusion’ mode.
2. Quickly triple-press the Z-Wave network button, then release it. Wait for the inclusion process to finish.
Exclusion
1. Put your home automation controller into Z-Wave ‘exclusion’ mode.
2. Quickly triple-press the Z-Wave network button. Wait for the exclusion process to finish.
Reset (Use this procedure to reset HS-LS100+ to factory settings when the Z-Wave controller is missing or
inoperable).
1. Press and hold the Z-Wave button for 20 seconds. Release the button once the LED stops blinking and glows
solidly.
Physical Installation
Free-standing installation: Simply place the leak sensor on a flat horizontal surface in the area where a leak might
occur.
Remote installation: Install the included magnetic wall mount/wired probe assembly in the location of your choice
(using the supplied mounting hardware) and attach the HS-LS100+ to it by aligning the 3 probes with the 3 holes in
the mounting bracket. Position and install the wired probe in the area where a leak might occur or where you wish
to detect liquid.
Leak Sensor Operation
HS-LS100+ is designed to transmit a Z-Wave command when liquid is sensed. It will also transmit another command
when liquid is no longer sensed.
Shock Sensor Operation
The shock sensor is designed to transmit a Z-Wave command when HS-LS100+ has been physically moved. This
sensor is especially helpful in determining whether the unit has been removed from its mount or tampered with.
Battery Sensor Operation
The battery sensor is designed to report battery level with a Z-Wave command every 43200 seconds (12 hours). If

Summary

Product Overview and Applications

Overview

Compact, easy to install Z-Wave leak sensor for automation events.

Applications

Activates Z-Wave devices or triggers home automation on leak detection.

Configuration and Installation

Z-Wave Network Inclusion

Add the HS-LS100+ sensor to your Z-Wave network.

Z-Wave Network Exclusion

Remove the HS-LS100+ sensor from your Z-Wave network.

Factory Reset

Reset the HS-LS100+ to factory settings.

Physical Installation Options

Free-standing or remote installation using magnetic mount.

Sensor Operations

Leak Sensor Operation

Transmits Z-Wave commands when liquid is sensed and when it is no longer sensed.

Shock Sensor Operation

Transmits Z-Wave command when the unit is physically moved.

Battery Sensor Operation

Reports battery level via Z-Wave command periodically.

Z-Wave Association and Notifications

Z-Wave Association Groups

Details on Group 1 (Lifeline) and Group 2 (Basic Set) associations.

Notification Types and Events

Supported Z-Wave notification types and associated events.

Advanced Configuration Parameters

Basic Set Command Configuration

Configure basic set command behavior and values for leak detection.

Temperature Trigger Settings

Set high and low temperature trigger values.

Leak Report Interval

Configure the interval for leak reports.

Shock Sensor and LED Settings

Enable shock sensor and blinking LED during alarms.

Specifications and Warranty

Technical Specifications

Operating temperature, Z-Wave frequency range, and dimensions.

Limited Warranty Information

Details on repair or replacement for defective devices.

HomeSeer HS-LS100+ Specifications

General

Brand	HomeSeer
Model	HS-LS100+
Category	Accessories
Language	English