HomeSeer HS-WX300 - User Manual

Products / ... / HS-WX300
HS-WX300 User Guide
Online manual for the HS-WX300 In-wall Dimmer & Switch
Overview
HS-WX300 is a Z-Wave in-wall light switch that may be configured to operate as either a dimmer switch or an on/off switch. It may be
installed with or without a neutral wire and it works with both wired and wireless companion switches in 3-way circuit configurations. This
switch has been designed, tested and certified for use in the United States and Canada.
Important
WARNING RISK OF FIRE | RISK OF ELECTRICAL SHOCK | RISK OF BURNS
DO NOT USE THIS SWITCH TO CONTROL ANYTHING THAT MAY PRESENT A HAZARD WHEN CONTROLLED REMOTELY OR
USED IN AN UNATTENDED FASHION. DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENTS.
CAUTION:
To Reduce the Risk of Overheating And Possible Damage To Other Equipment, Do Not Install To Control A Receptacle, A Motor-
Operated Appliance, A Fluorescent Lighting Fixture, Or A Transformer-Supplied Appliance.
If used with non-dimming loads, be sure to configure as a an on-off switch before powering the load.
Circuit Types
Most lighting loads are powered with line (120 VAC) and neutral wires. The line wire always runs through the wall switch box but the
neutral may not be present there. If the neutral wire is present, use the 3-wire method below. If no neutral is present, use the 2-wire
method. For 3-way circuits, a neutral is only required at the companion switch location (using HS-WA100+ or standard 3-way switches).
Single Switch, 3-Wire Circuit Single Switch, 2-Wire Circuit
Multi Switch (3-Way) Wiring for 2-Wire & 3-Wire Circuits
Installation
Products
Hubs

Software

Interfaces

Lighting

HS-WX300

HS-WX300 User Guide
HS-WX300 vs HS-WD200+
How To Add HS-WX300+ to Sma…
HS-WA100+

HS-SP100
HS-FC200+

HS-WD200+

HS-WS200+

HS-WD100+
WD/WS Manual Reset
Compatible Wire Gauge
Legacy Lighting

Sensors

Water Valves

IP Cameras

MyHS

Cloud Services

Plugin SDK
Return Policy
Other Docs


Summary

HS-WX300 Product Overview and Safety

Overview

General description of the HS-WX300 Z-Wave in-wall dimmer and switch.

Important Safety Warnings

Critical safety precautions regarding fire, electrical shock, and burns.

Circuit Wiring Types

Explanation of 2-wire and 3-wire configurations for lighting loads.

Installation and Configuration

Installation Steps

Step-by-step guide for installing the HS-WX300 switch.

Configuration Options

Settings for switch mode, wire mode, Z-Wave inclusion, and factory reset.

Changing Switch Mode

Procedure to configure the switch as a dimmer or an on-off switch.

Changing Wire Mode

Procedure to select between 3-wire and 2-wire installation modes.

Operation and Advanced Features

Association Setup

How to configure Group 1 and Group 2 associations for Z-Wave devices.

Device Operation

Methods for controlling the switch locally and remotely via Z-Wave.

HomeSeer Compatibility

Information on how the switch works with HomeSeer systems.

Advanced Features

Details on multi-tap, RGB LEDs, toggle, smart bulb, and dim level features.

Technical Specifications and Compliance

Z-Wave Parameters

Configuration parameters for adjusting HS-WX300 settings via Z-Wave.

Supported Z-Wave Command Classes

List of Z-Wave command classes supported by the device.

Specifications

Electrical and environmental specifications for the HS-WX300.

Warranty and Compliance

Product warranty, FCC, and IC regulatory compliance statements.

HomeSeer HS-WX300 Specifications

General

Model	HS-WX300
Category	Switch
Type	Smart Dimmer Switch
Protocol	Z-Wave Plus
Frequency	60 Hz
Load Type	Incandescent, LED, CFL
Max Load (Incandescent)	600W
Max Load (LED/CFL)	150W
Neutral Wire Required	Yes
Dimming Range	0-100%
Color	White
Voltage	120V AC
Operating Temperature	32°F to 104°F
Compatibility	Z-Wave controllers