Homewerks 27-B423S-HW User Manual (English)

Questions and Answers:

J
Jose ChaseAug 13, 2025
What to do if water does not completely shut off in my Homewerks 27-B423S-HW?
- R
  ruthconnerAug 13, 2025
  If the water in your Homewerks plumbing product doesn't completely shut off, it might be due to a dirty, stuck, or broken rubber valve seat. Here's what you can do: 1. Shut off the water supply. 2. Remove the handle and loosen the bonnet. 3. Lift out the cartridge assembly. 4. Inspect the rubber valve seat for debris or damage. Remove any debris. If the seat is stuck, gently push it to ensure smooth movement. Ensure the spring is correctly placed underneath the valve seat. If the rubber valve seat is worn out or broken, you should replace the cartridge by calling customer service. 5. Position the cartridge back into the faucet body, aligning the ridges on the bonnet with the grooves on the faucet body. Tightly screw the bonnet onto the faucet body. 6. Reinstall the handle.
J
Joseph FrancisAug 20, 2025
What to do if Homewerks 27-B423S-HW water will not shut off?
- E
  Elizabeth BaileyAug 20, 2025
  If the water in your Homewerks plumbing product won't shut off when turning the handle to the off position, the cartridge is likely damaged. To resolve this: 1. Shut off the water supply. 2. Remove the handle and loosen the bonnet. 3. Lift out the cartridge assembly. 4. Replace the cartridge by calling customer service. 5. Position the cartridge back into the faucet body, aligning the ridges on the bonnet with the grooves on the faucet body. Tightly screw the bonnet onto the faucet body. 6. Reinstall the handle.
L
ltoddAug 25, 2025
Why is the LED light in my Homewerks Plumbing Product sensor flashing?
- D
  Debra MossAug 25, 2025
  If the LED light in your Homewerks plumbing product sensor is flashing continuously, it likely indicates a low battery level. To resolve this: 1. Turn the handle to the on position. 2. Wave your hand in front of the sensor. 3. If the sensor flashes slowly, replace the batteries in the battery pack with four new AA batteries.
W
waveryAug 28, 2025
What to do if Homewerks 27-B423S-HW Plumbing Product sensor is not activating?
- R
  rosalesrichardAug 28, 2025
  If the sensor on your Homewerks plumbing product is not activating the water flow, it could be due to a dirty sensor window or a broken sensor control box. * First, try cleaning the sensor window with a soft cloth, avoiding abrasive cleaners, steel wool, and harsh chemicals. * If cleaning doesn't work, the sensor control box may be broken, and you should replace it by calling Customer Service.
M
Mallory WhiteSep 1, 2025
How to fix a Homewerks 27-B423S-HW faucet that leaks around the aerator?
- J
  John MitchellSep 1, 2025
  If your Homewerks plumbing product faucet is leaking around the aerator, it could be improperly fitted, dirty, or have small parts that are improperly installed. Here’s how to fix it: 1. Remove the aerator from the spout by turning it clockwise. Inspect the black rubber packing inside the aerator to ensure it is flat. 2. Screw the aerator back onto the spout and tighten it.
A
Antonio AndersonSep 4, 2025
Why does my Homewerks 27-B423S-HW faucet have an improper water pattern?
- K
  Kyle FlemingSep 4, 2025
  An improper water pattern in your Homewerks plumbing product faucet is likely due to a dirty aerator or small parts inside the aerator being improperly installed. To correct this: 1. Remove the aerator from the spout by turning it clockwise. 2. Gently flush the small parts inside the aerator to clear away any debris. 3. Reinstall the small parts as shown in the replacement parts exploded diagram. Ensure metal screens are flat and the plastic supporter is straight. 4. Screw the aerator back onto the spout and tighten.
C
Caleb CarsonSep 8, 2025
What causes low water flow in Homewerks 27-B423S-HW Plumbing Product?
- H
  Hannah HardingSep 9, 2025
  If you're experiencing low water flow in your Homewerks plumbing product, the issue might be a dirty or damaged washer on the "in" end of the sensor control box. Here's how to address it: 1. Remove the hose and unscrew the connector. 2. Remove the washer from the control box. 3. Clean the washer of any debris or replace it if damaged. 4. Reassemble the connector and hose.

Homewerks 27-B423S-HW Specifications

General

Product Type	Shower head
Finish	Brushed Nickel
Color/Finish Family	Nickel
Color	Brushed Nickel
Flow Rate	1.75 GPM
Installation Type	Wall Mount
Weight	0.44 lb
Material	Acrylonitrile Butadiene Styrene (ABS)