To Next PageTo Next PageWhy Honda Snow Blower engine won't start?
Your Honda Snow Blower engine might not be starting because the engine switch is OFF. Ensure the engine switch is turned ON. Also, check if the fuel valve is OFF and turn it ON. Stale or old fuel can also prevent starting, so use fresh fuel and drain the carburetor. Make sure the spark plug cap is connected and that the spark plug is free of deposits and has the proper gap.
What to do if Honda HS720AM auger does not operate?
If your Honda Snow Blower's auger isn't working, the auger paddles may be worn out and need replacement. Ensure the auger clutch lever is fully engaged by pulling it toward the handlebar. If the clutch lever free play is excessive, it should be adjusted.
How to troubleshoot Honda HS720AM electric starter not working?
If the electric starter on your Honda Snow Blower isn't working, it could be due to no electric power from the outlet. Try using a known good electrical outlet. Another possibility is a defective power cord, so try another power cord.
What to do if my Honda HS720AM Snow Blower engine switch is OFF?
If your Honda Snow Blower won't start, make sure the engine switch is turned ON.
What to do if my Honda HS720AM Snow Blower has stale or old fuel?
If your Honda Snow Blower has stale or old fuel, be sure to fill the tank with fresh fuel and drain the carburetor.
What to do if my Honda HS720AM spark plug cap is off?
Make sure the spark plug cap is securely connected.
What to do if my Honda Snow Blower fuel valve is OFF?
If the fuel valve is OFF, turn the fuel valve ON.
What to do if my Honda HS720AM Snow Blower spark plug cap is not secure?
Ensure the spark plug cap is securely connected.
What to do if my Honda Snow Blower has no electric power from the outlet?
Try a known good electrical outlet or start the engine by using the recoil starter.
What to do if my Honda HS720AM Snow Blower power cord is defective?
Try another power cord or start the engine using the recoil starter.
General| Starting System | Recoil |
|---|---|
| Clearing Width | 20 inches |
| Clearing Height | 12 inches |
| Weight | 92 lbs |
| Type | Single-Stage |
| Stages | 1 |
| Intake Height | 12 inches |
| Auger Material | Steel |
| Chute Control | Manual |
| Engine Type | 4-stroke |
| Throw Distance | 33 ft |
| Auger Type | Steel |
| Fuel Tank Capacity | 0.25 gal |
Your safety and the safety of others are very important. Read safety messages carefully.
Find safety information in labels, instructions, and safety messages (DANGER, WARNING, CAUTION).
Labels warn of potential hazards. Read them carefully for hazard information.
Tools required and list of loose parts for initial setup of the snow thrower.
Step-by-step guide to adding engine oil before the first use.
Instructions on how to register your snow thrower for service information.
Essential sections to read before operating the snow thrower for the first time.
Pre-operation inspection to ensure the snow thrower is in safe working condition.
Inspect the operating area for hazards before starting.
Procedure to check and add engine oil to the correct level.
Inspect the scraper blade for wear and proper adjustment.
Safety warning about the dangers of the rotating auger and how to clear clogs.
Inspect the area and remove hazards before operation.
Importance of keeping safety shields for protection from moving parts.
Safety instructions for refueling the snow thrower.
Procedure to turn off the engine when leaving the snow thrower unattended.
Guidelines for safe operation on slopes.
Controls the fuel flow to the carburetor.
Controls the engine ignition system.
Controls the engine ignition system using a key.
Button to operate the electric starter.
Controls the fuel mixture for starting and warm-up.
Controls the discharge chute direction and distance remotely.
Controls the discharge chute direction left or right remotely.
Engages the auger paddles and propels the snow thrower forward.
Procedure for starting the engine using the electric starter.
Procedure for starting the engine using the manual recoil starter.
General safety precautions to follow during maintenance procedures.
Specific safety measures to prevent hazards during maintenance.
Procedure for changing the engine oil according to the maintenance schedule.
Inspection and adjustment procedure for auger clutch lever free play.
Inspection and adjustment procedure for belt tension.
Preparation steps for fuel system storage.
Preparation steps for engine oil during storage.
Troubleshooting steps for when the electric starter does not work.
Troubleshooting steps for when the engine fails to start.
Troubleshooting steps for when the engine runs but the auger doesn't.
Troubleshooting steps for when the discharge chute does not turn.
Troubleshooting steps for when the engine has low power.
Troubleshooting steps for when snow is not discharged correctly.
Troubleshooting steps for when the engine stalls with the clutch engaged.
Location of engine and frame serial numbers for reference.
Information on operating the snow thrower at high altitudes.
Details about the engine's emission control system and related information.
Key features of the snow thrower models.
Specifications for the snow thrower's physical dimensions and weight.
Information on purchasing parts, accessories, and service items.
How to find an authorized Honda servicing dealer.
Contact information for Honda Power Equipment customer support.
List of available Honda publications for snow throwers.
Information on where to find answers to common questions.
