To Next PageTo Next PageWhy is not enough spine glue being applied by my Horizon Fitness Binding Machine?
If not enough spine glue is being applied by your Horizon Fitness Binding Machine, it could be because: * The spine glue is turned OFF. Turn the spine glue ON. * The setting for spine glue is too low. Increase the spine glue amount. * The wiper opening is too narrow. Increase the wiper opening.
What to do if the cover sheets jam in Horizon Fitness Binding Machine?
If the cover sheets jam in your Horizon Fitness Binding Machine, consider the following possible causes: * The jog guides and the positioning guides are not aligned with each other. Adjust the jog guide and the positioning guides for a clearance of 3 mm (0.12”). * The cover sheets are curled. Uncurl the cover sheets. * The position of the upper cover guide is not correct. Set the upper cover guide at the edge of the cover sheet. * A transport belt is missing. Install the missing transport belt.
Why is too much side glue applied by my Horizon Fitness Binding Machine?
Too much side glue may be applied by your Horizon Fitness Binding Machine if: * The side glue roller distance is too wide. Make the distance narrower. * The nipper height is too high, and the spilled glue leaks to the side. Reduce the nipper height. * The gap between the side glue roller and the glue amount adjusting plate is too wide. Reduce the gap.
Why is not enough side glue being applied by my Horizon Fitness Binding Machine?
If not enough side glue is being applied by your Horizon Fitness Binding Machine, it could be due to several reasons: * The side glue is turned OFF. Turn the side glue ON. * The side glue roller distance is too narrow. Make the distance wider. * The gap between the side glue roller and the glue amount adjusting plate is too small. Widen the gap.
What to do if there are a lot of paper chips around the milling section of my Horizon Fitness Binding Machine?
If there are a lot of paper chips around the milling section of your Horizon Fitness Binding Machine, it could be because: * The trimmings bag is full or clogged. Remove the paper chips from the bag. * The hose is clogged with trimmings. Remove the trimmings from the hose. * Trimmings are clogged inside the milling unit. Clean the milling unit. * The breaker of the milling blower is tripped. Check if the breaker is not tripped. If the breaker trips repeatedly, please call your local dealer.
Why is too much spine glue applied by my Horizon Fitness Binding Machine?
Too much spine glue may be applied by your Horizon Fitness Binding Machine if the setting for spine glue is too high, so decrease the spine glue amount. Another possible cause is that the wiper opening is too wide, so reduce the wiper opening.
What should I do if glue is not melted in my Horizon Fitness Binding Machine?
If the glue in your Horizon Fitness Binding Machine is not melted, check if the breaker of the heater is tripped. If the breaker trips repeatedly, please call your local dealer.
General| Brand | Horizon Fitness |
|---|---|
| Model | BQ-270 |
| Category | Binding Machine |
| Language | English |
Explains the meaning of warning, caution, note, and prohibition symbols used in the manual.
Lists critical safety warnings and cautions for operating the machine safely.
Describes the safety features of the BQ-270, such as sensors and emergency stop buttons.
Guides users on inputting job parameters like binding mode, size, and function settings.
Covers detailed adjustments for clamp, glue, nipping, scoring, and cover sheet settings.
Covers powering on the machine and performing essential safety function checks before operation.
Step-by-step guide to inputting necessary job details like binding type, size, and settings.
Outlines the sequence of steps for starting, adding sheets, and finishing the binding process.
Lists common problems with booklet quality and their causes and remedies.
Explains error codes, their causes, and remedies, with service call indications.
Guide on troubleshooting machine issues related to tripped circuit breakers.
Covers physical installation, including moving the clamp, leveling, and wiring.
