To Next PageTo Next PageWhat to do if my Hotpoint Ariston Dishwasher does not start?
If your Hotpoint Ariston Dishwasher isn't starting, first ensure the plug is properly inserted into the electrical socket and that there is power in the house. Also, verify that the dishwasher door is completely shut. If a delayed start has been programmed, refer to Start-up and use to cancel the delayed start.
Why is there no water draining from my Hotpoint Ariston LL 42 Dishwasher?
If water isn't draining from your Hotpoint Ariston Dishwasher, it might be because the cycle hasn't finished yet. If the cycle is complete, check the water inlet hose for kinks and clear any blockages in the drain duct. Food residues clogging the filter can also cause this; clean the filter as per Care and maintenance.
Why is my Hotpoint Ariston Dishwasher not cleaning dishes properly?
If your Hotpoint Ariston Dishwasher isn't cleaning dishes well, several factors could be at play. Check if the racks are overloaded and rearrange the crockery properly. Ensure the sprayer arms can move freely and that you've selected a suitable wash cycle. Excessive foam, a wrongly closed rinse aid compartment lid, a dirty filter, or a low refined salt level can also cause this issue. Make sure the detergent has been measured out correctly or is suitable for use in dishwashers. Clean or replace the filter and check the refined salt level.
Why are there white film or limescale deposits on dishes and glasses in my Hotpoint Ariston LL 42?
If your dishes and glasses are covered in a white film or limescale deposits after using your Hotpoint Ariston Dishwasher, it could be due to several reasons. The refined salt level might be low, or the dosage setting isn't suited to the water's hardness; check and adjust these. Ensure the lid on the salt dispenser is closed correctly. Also, the rinse aid may have been used up, or the dosage is too low; refill or adjust as needed. Lastly, if the crockery is made from non-stick material, use dishwasher-compatible dishes.
Why does my Hotpoint Ariston LL 42 Dishwasher make excessive noise?
Excessive noise from your Hotpoint Ariston Dishwasher can be caused by dishes rattling against each other or the sprayer arms; rearrange them to prevent this. It can also be due to an excessive amount of foam; ensure the detergent is measured out correctly and is suitable for dishwashers.
Why are my dishes not drying properly in my Hotpoint Ariston Dishwasher?
If your dishes aren't drying properly in your Hotpoint Ariston Dishwasher, the rinse aid may have been used up, or the dosage is too low; refill or adjust it. The rinse aid dispenser setting might also be too low; increase it. Finally, ensure you've selected a wash cycle that includes drying.
Why do the dishes and glasses have streaks or a bluish tinge after using my Hotpoint Ariston LL 42?
If your dishes and glasses have streaks or a bluish tinge after using your Hotpoint Ariston Dishwasher, the rinse aid dosage might be too high. Adjust the rinse aid dosage as per Rinse aid and salt.
What to do for foam or blocked filter alarm on Hotpoint Ariston LL 42 Dishwasher?
If you are experiencing a foam or blocked filter alarm on your Hotpoint Ariston Dishwasher: - Switch off the appliance by pressing the ON/OFF button. - Ensure that a suitable detergent is used. - Check that the lid on the rinse aid compartment is shut correctly. - Remove any food residues from the filters. - Replace the filter assembly correctly and switch the machine back on.
What to do if my Hotpoint Ariston LL 42 does not take any water in / Tap shut-off alarm?
If your Hotpoint Ariston Dishwasher isn't taking in water and the tap shut-off alarm is on, make sure there is water in the mains supply. Check the water inlet hose for any bends. If the appliance lock has been activated due to inaction after beeps, switch off the machine using the ON/OFF button, turn on the tap, and switch the machine back on after 20 seconds.
What to do for water intake solenoid valve malfunction alarm on Hotpoint Ariston LL 42 Dishwasher?
If you get a water intake solenoid valve malfunction alarm on your Hotpoint Ariston Dishwasher: - Switch off the appliance by pressing the ON/OFF button and switch it back on after a minute. - If the alarm continues, shut off the water tap to eliminate the risk of flooding. - Shut off the water tap. - Remove the plug from the electrical socket and contact Assistance.
General| Brand | Hotpoint Ariston |
|---|---|
| Model | LL 42 |
| Category | Dishwasher |
| Language | English |
Instructions for safely connecting water and power sources to the dishwasher.
Instructions for safely connecting the dishwasher to the electrical power supply.
Step-by-step guide to initiating a wash cycle.
Procedures for safely disconnecting power and water before cleaning.
Essential safety rules for operating the dishwasher.
Solutions for when the appliance fails to power on or begin a cycle.
Causes and fixes for drainage issues.
Troubleshooting steps for incomplete cleaning of dishes.
Diagnosing and resolving water intake problems or tap shut-off alarms.
Addressing alarms related to excessive foam or blocked filters.
Identifying and resolving alarms indicating a malfunction in the water intake system.
Steps to take before contacting technical support.
