EasyManua.ls Logo

Hotpoint NM11946BCAUK - User Manual

Hotpoint NM11946BCAUK
4 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GB
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set wash cycle 3 with a temperature of 40°C.
3) Long synthetics cycle: set wash cycle 4 with a temperature of 40°C.
* By selecting the 14 cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
*** For Prewash press the “Temp.” button until the symbol lights up (only 90°).
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
Maximum load 9 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Active
Care
(
)
Add
Gar-
ments
(
)
Detergents and
Additives
Recommended
detergent
Residual damp-
ness %
Energy consump-
tion kWh
Total water l
Wash cycle
Temperature
Max.
spin speed
(rpm)
Max.
load
(kg)
Duration
(min-
utes)
Pre-
wash
Wash
Fabric
softener
Powder Liquid
Default Range 1 2 3
1 Mixed
40°C - 40°C
1400 9
**
–
–
– – –
2
Eco Cotton
(1)
60°C
60°C 1400 9 225
–
–
53 0,87 57,5
40°C 1400 9 235
–
–
53 1,24 94
3 Cotton (2)
40°C - 60°C
1400 9 235
–
–
53 1,24 94
4 Synthetics (3)
40°C - 60°C
1200 4,5 175
–
–
53 0,54 55
5 Delicates
40°C - 40°C
1000 4,5
**
–
–
– – –
6
Wool
40°C - 40°C
800 2
** –
–
–
– – –
7 Anti Allergy
60°C - 60°C
1400 5
** –
–
– – –
8 Anti Stain 40°
40°C - 40°C
1000 4,5
**
–
–
– – –
9 White
40°C - 90°C
1400 9
**
(***)
– – –
10 Steam Refresh
– – – 2 ** – – – – – – – – – –
11 Rapid 30 min
30°C - 30°C
800 4,5
**
–
–
– – –
12 Bed & Bath
60°C - 60°C
1400 9
**
–
– – –
13 Shirts
40°C - 40°C
600 2
** –
–
–
– – –
14 Spin & Drain *
– –
1400 9
** – – – – – – – – – –
15 Rinse & Spin
– –
1400 9
** – – – –
– – – – –
Required dosage Optional dosage
DETERGENT DISPENSER DRAWER
compartment 1: Pre-wash detergent
(powder)
compartment 2: Detergent for the wash
cycle (powder or liquid)
If liquid detergent is used, it is recommended
that the removable plastic partition A
(supplied) be used for proper dosage.
If powder detergent is used, place the partition
into slot B.
compartment 3: Additives (fabric softeners,
etc.)
The fabric softener should not overow the grid.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
1
2
3
A
B
1. STEAM HYGIENE / MUTE button
2. FINAL CARE / KEY LOCK button
3. ON/OFF button
4. ACTIVE CARE button and indicator light
5. START/PAUSE button
6. RAPID / ECO button
7. SPIN button
8. START DELAY button
9. TEMPERATURE button
10. WASH CYCLE SELECTOR KNOB
1 2
4
5
67
8
9
3
10
DISPLAY

Questions and Answers

  • M
    Morgan BurnsJul 31, 2025
    What to do if my Hotpoint NM11946BCAUK Washer does not fill with water?
    • P
      Peter CortezAug 1, 2025
      If your Hotpoint Washer isn't filling with water and displays the “ ” symbol, check that the water inlet hose is connected to the tap and not bent. Also, make sure the water tap is open, there's a water supply in the house, the water pressure isn't too low, and the START/PAUSE button has been pressed.
  • L
    leenancyAug 4, 2025
    What to do if the wash cycle on my Hotpoint Washer doesn't start?
    • W
      woodashleyAug 5, 2025
      If your Hotpoint Washer's wash cycle won't start, make sure the door is properly closed, the ON/OFF button and the START/PAUSE button have been pressed, the water tap is open, no delay has been set, and that Demo Mode is deactivated.
  • C
    Christina SantiagoAug 9, 2025
    What to do if my Hotpoint NM11946BCAUK won't drain and shows error F9E1?
    • S
      slloydAug 9, 2025
      If your Hotpoint Washer does not drain and shows the symbol (F9E1) on the display, try cleaning the pump filter and check if the drain hose is bent or the drainage duct is clogged.
  • E
    Erin FrederickAug 14, 2025
    Why is my Hotpoint Washer vibrating so much?
    • D
      David SullivanAug 14, 2025
      If your Hotpoint Washer vibrates excessively during the spin cycle, it might be due to transport bolts not being removed during installation, the machine not being leveled, or the washer being wedged between furniture and the wall. Check these aspects to resolve the issue.
  • M
    Melissa BarreraAug 18, 2025
    Why does my Hotpoint NM11946BCAUK keep filling and draining water?
    • H
      Heather McgeeAug 18, 2025
      If your Hotpoint Washer continuously loads and unloads water, check that the drain hose is fitted between 65 and 100 cm from the floor and that the free end of the hose is not immersed in water. Also, ensure that the wall drainage system has a breather pipe. If you live on one of the upper floors of a building, there may be problems relating to back-siphonage. Special anti-siphon valves are available in shops and help to prevent this inconvenience.
  • C
    Carrie LaneAug 22, 2025
    Why is there too much foam in my Hotpoint NM11946BCAUK Washer?
    • M
      Miguel WeissAug 22, 2025
      If there is too much foam in your Hotpoint Washer, it might be because the detergent isn't suitable for machine washing. Look for detergents labeled “for washing machines” or “hand and machine wash”. Also, you may have used too much detergent.
  • J
    johnstonjenniferAug 27, 2025
    What does it mean when the “Spin&Drain” icon blinks on my Hotpoint NM11946BCAUK Washer?
    • D
      denise98Aug 27, 2025
      If the “Spin&Drain” phase icon blinks and “0” spin speed is displayed on your Hotpoint Washer, it means an unbalance of laundry load prevented spin cycle, to protect the washing machine. If you want to spin the wet laundry, add more laundry items of different sizes and start “Spin&Drain” programme. Avoid small laundry loads consisting of few big, absorbent pieces of laundry / wash different sizes of articles in one load.

Summary

Quick Guide

Control Panel Overview

Identifies and describes the buttons and functions on the washing machine's control panel.

Wash Cycle Table

Details available wash cycles, including temperature, spin speed, load capacity, and consumption data.

Detergent Dispenser Drawer

Provides instructions on how to correctly use the detergent and additive compartments.

Wash Cycles

Eco Cotton Cycle

Display Information

Display Error Codes

Lists common error codes and their meaning, such as 'Call Service' or 'Water filter clogged'.

Operating the Washing Machine

Pausing and Resuming Cycles

Instructions on how to pause a wash cycle and then restart it.

Adding Garments

Changing a Running Cycle

Troubleshooting

Machine Not Starting

Solutions for common issues when the washing machine does not power on or start.

Water Filling Problems

Troubleshooting steps for when the machine does not fill with water.

Drainage Issues

Resolving problems related to the machine not draining or continuously loading/unloading water.

Excess Foam and Vibration

Hotpoint NM11946BCAUK Specifications

General IconGeneral
Appliance typeWashing Machine
Capacity9 kg
Spin speed1400 RPM
Energy ratingA
Spinning efficiency classB
Noise level washing52 dB
Number of programmes16
Height85 cm
Width60 cm
Depth54 cm
ColourWhite
Delay startYes
Child lockYes
Drum materialStainless Steel
Loading typeFront Load

Related product manuals