EasyManua.ls Logo

Hotsy 1700 Series - User Manual

Hotsy 1700 Series
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
8.914-380.0 - W 08/01/17
1700 Series
Cold Water - Electric Powered -
Stationary
Operator’s Manual
Pressure Washer
MODELS: 1.106-511.0
1710
1.106-512.0
1720
1.106-513.0
1722
1.106-514.0
1723
1.106-515.0
1724
1.106-516.0
1725
1.106-529.0
1743
1.106-530.0
1744
1.106-531.0
1745
1.106-534.0
1753
1.106-535.0
1754
1.106-536.0
1755
For the Hotsy Dealer nearest you,
consult our web page at
www.hotsy.com

Table of Contents

Other manuals for Hotsy 1700 Series

Preview: Operating Instructions And Parts Manual
Operating Instructions And Parts Manual42 pages

Questions and Answers

  • M
    mgarciaNov 23, 2025
    How to fix low operating pressure on my Hotsy 1700 Pressure Washer?
    • R
      Robert BlakeNov 24, 2025
      To address low operating pressure in your Hotsy Pressure Washer, consider these potential causes and solutions: * **Insufficient water supply:** Use a larger supply hose and clean the filter at the water inlet. * **Old, worn, or incorrect spray nozzle:** Match the nozzle number to your machine or replace it with a new nozzle. * **Obstruction in spray nozzle:** Remove any obstruction. * **Plumbing or hose leak:** Check the plumbing system for leaks and re-tape any leaks with Teflon tape. * **Insufficient power supply:** Check the voltage. * **Belt slippage:** Tighten or replace the belt, ensuring you use the correct belt. * **Worn packing in pump:** Install a new packing kit. * **Fouled or dirty inlet or discharge valves in pump:** Clean the inlet and discharge valves. * ...
  • A
    Alexander ThomasAug 27, 2025
    Why does my Hotsy Pressure Washer system stop and restart after a few seconds?
    • S
      Samuel MilesAug 27, 2025
      If your Hotsy Pressure Washer system stops after approximately four seconds and then restarts, it could be due to a faulty pressure switch (check and replace) or a leak at the discharge line (check for leaks at the hose and spray gun).
  • W
    wallacebrianAug 29, 2025
    Why won't my Hotsy 1700 Pressure Washer start when I pull the spray gun trigger?
    • C
      Christopher DuncanAug 29, 2025
      If your Hotsy Pressure Washer machine will not start when the spray gun trigger is pulled, it could be due to a loss of electrical power (check the circuit breaker) or a faulty on/off switch, pressure switch, timer, or magnetic contactor (test and replace as needed).
  • T
    Tyler CervantesAug 30, 2025
    Why does the motor “hum” but not turn on my Hotsy 1700 Pressure Washer?
    • J
      jessica64Aug 30, 2025
      A motor that “hums” but does not turn on your Hotsy Pressure Washer indicates electric motor single phasing. Check for a blown fuse or a loose power line.
  • C
    Cindy RaySep 1, 2025
    Why is the pressure low after normal use on my Hotsy 1700?
    • E
      Emily PetersonSep 1, 2025
      If the pressure is low on your Hotsy Pressure Washer after a period of normal use, there are several things to check. The nozzle may be worn, so inspect and replace it if necessary. Also, the inlet or discharge valves could be worn or blocked; check and replace or clean them as needed. Finally, the unloader valve seat might be worn, so check and replace it if necessary.
  • C
    Christine BarrettNov 22, 2025
    How to fix low operating pressure in my Hotsy 1700 Pressure Washer?
    • K
      kelleyaprilNov 22, 2025
      To troubleshoot low operating pressure in your Hotsy Pressure Washer, start by checking for common issues. Ensure you have a sufficient water supply, using a larger supply hose and cleaning the filter at the water inlet. Inspect the spray nozzle; it might be old, worn, or incorrect, so match the nozzle number to your machine or replace it. Also, check for belt slippage and tighten or replace the belt if needed, ensuring you use the correct belt. Examine the plumbing system for leaks and re-tape any leaks with Teflon tape. Other potential causes include a faulty pressure gauge (install a new gauge), worn packing in the pump (install a new packing kit), fouled or dirty inlet or discharge valves in the pump (clean them), worn inlet or discharge valves (replace with a valve kit), an obstructio...
  • E
    ericarhodesSep 23, 2025
    How to reduce noise coming from the pump of my Hotsy Pressure Washer?
    • M
      Michelle BlackSep 23, 2025
      Excessive noise from your Hotsy Pressure Washer's pump can be due to: * **Air in the suction line:** Check the water supply and connections on the suction line. * **Broken or weak inlet or discharge valve springs:** Check and replace if necessary. * **Foreign matter in valves:** Check and clean if necessary. * **Worn bearings:** Check and replace if necessary. * **Excessive temperature of liquid:** Reduce the liquid temperature to below 75°C (160°F).
  • J
    jeremy95Nov 21, 2025
    Why is the operating pressure low on my Hotsy 1700 Pressure Washer?
    • K
      Kevin PadillaNov 21, 2025
      Low operating pressure in your Hotsy Pressure Washer can stem from several causes. It may be due to a faulty pressure gauge, in which case you should install a new one. Insufficient water supply can also be the culprit; try using a larger supply hose and cleaning the filter at the water inlet. Other potential causes include an old, worn, or incorrect spray nozzle (match the nozzle number to the machine or replace it), belt slippage (tighten or replace the belt), plumbing or hose leaks (check and retape with Teflon tape), worn pump packing (install a new kit), fouled or dirty inlet/discharge valves (clean them), worn valves (replace with a valve kit), obstruction in the spray nozzle (remove it), a leaking pressure control valve (rebuild or replace it), or insufficient power supply (check th...
  • P
    Phillip MoranSep 12, 2025
    Why does oil squirt out of the oil cap on my Hotsy 1700 pump?
    • R
      Robert LoweSep 12, 2025
      If oil squirts out of the oil cap on your Hotsy Pressure Washer pump, it's likely that the pump is overfilled with oil. Maintain the oil level halfway up on the sight glass at the rear of the pump or at the top of the notch on the dipstick (where applicable).
  • C
    Courtney CarterSep 8, 2025
    Why does the motor strain under load on my Hotsy 1700?
    • K
      kathleenwardSep 8, 2025
      If your Hotsy Pressure Washer's motor strains under load, it could be due to a faulty motor (send to the nearest Baldor repair center), an incorrect spray nozzle (install the proper nozzle size as indicated on the serial plate), or an obstruction in the spray nozzle (remove the obstruction).

Hotsy 1700 Series Specifications

General IconGeneral
BrandHotsy
Model1700 Series
CategoryPressure Washer
LanguageEnglish

Related product manuals