Hotsy 1710 SS - User Manual

18 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

8.914-380.0 - BJ 06/07/22

1700 Series

Cold Water - Electric Powered -

Stationary

Operator’s Manual

Pressure Washer

MODELS:

1 . 1 0 6 - 5 1 1 . 0

1710

1.106-512.0

1720

1.106-513.0

1722

1.106-514.0

1723

1.106-515.0

1724

1.106-516.0

1725

1.106-529.0

1743

1.106-530.0

1744

1.106-531.0

1745

1.106-534.0

1753

1.106-535.0

1754

1.106-536.0

1755

1.106-590.0

1726

1.106-591.0

1746

1.106-592.0

1756

1.106-593.0

1710 SS

1.106-594.0

1720 SS

1.106-595.0

1722 SS

1.106-596.0

1723 SS

1.106-597.0

1724 SS

1.106-598.0

1725 SS

1.106-599.0

1743 SS

1.106-600.0

1744 SS

1.106-601.0

1745 SS

1.106-602.0

1755 SS

For the Hotsy Dealer nearest you,

consult our web page at

www.hotsy.com

Questions and Answers

D
dmarksNov 24, 2025
How to fix low operating pressure on my Hotsy 1710 SS?
- A
  Amber EscobarNov 24, 2025
  To address low operating pressure in your Hotsy Pressure Washer, consider these potential causes and solutions: * **Insufficient water supply:** Use a larger supply hose and clean the filter at the water inlet. * **Old, worn, or incorrect spray nozzle:** Match the nozzle number to your machine or replace it with a new nozzle. * **Obstruction in spray nozzle:** Remove any obstruction. * **Plumbing or hose leak:** Check the plumbing system for leaks and re-tape any leaks with Teflon tape. * **Insufficient power supply:** Check the voltage. * **Belt slippage:** Tighten or replace the belt, ensuring you use the correct belt. * **Worn packing in pump:** Install a new packing kit. * **Fouled or dirty inlet or discharge valves in pump:** Clean the inlet and discharge valves. * ...
S
Sally ChangAug 27, 2025
Why does my Hotsy Pressure Washer system stop and restart after a few seconds?
- V
  victoria50Aug 28, 2025
  If your Hotsy Pressure Washer system stops after approximately four seconds and then restarts, it could be due to a faulty pressure switch (check and replace) or a leak at the discharge line (check for leaks at the hose and spray gun).
P
Pamela ShieldsAug 29, 2025
Why won't my Hotsy Pressure Washer start when I pull the spray gun trigger?
- M
  Mallory BakerAug 29, 2025
  If your Hotsy Pressure Washer machine will not start when the spray gun trigger is pulled, it could be due to a loss of electrical power (check the circuit breaker) or a faulty on/off switch, pressure switch, timer, or magnetic contactor (test and replace as needed).
R
Richard MartinezAug 30, 2025
Why does the motor “hum” but not turn on my Hotsy 1710 SS?
- K
  kimberly93Aug 30, 2025
  A motor that “hums” but does not turn on your Hotsy Pressure Washer indicates electric motor single phasing. Check for a blown fuse or a loose power line.
L
lawrencemichaelSep 1, 2025
Why is the pressure low after normal use on my Hotsy 1710 SS Pressure Washer?
- R
  Richard ScottSep 1, 2025
  If the pressure is low on your Hotsy Pressure Washer after a period of normal use, there are several things to check. The nozzle may be worn, so inspect and replace it if necessary. Also, the inlet or discharge valves could be worn or blocked; check and replace or clean them as needed. Finally, the unloader valve seat might be worn, so check and replace it if necessary.
S
Sean MooreNov 22, 2025
How to fix low operating pressure in my Hotsy 1710 SS?
- L
  Lisa JacksonNov 22, 2025
  To troubleshoot low operating pressure in your Hotsy Pressure Washer, start by checking for common issues. Ensure you have a sufficient water supply, using a larger supply hose and cleaning the filter at the water inlet. Inspect the spray nozzle; it might be old, worn, or incorrect, so match the nozzle number to your machine or replace it. Also, check for belt slippage and tighten or replace the belt if needed, ensuring you use the correct belt. Examine the plumbing system for leaks and re-tape any leaks with Teflon tape. Other potential causes include a faulty pressure gauge (install a new gauge), worn packing in the pump (install a new packing kit), fouled or dirty inlet or discharge valves in the pump (clean them), worn inlet or discharge valves (replace with a valve kit), an obstructio...
R
Ronald LawrenceSep 23, 2025
How to reduce noise coming from the pump of my Hotsy 1710 SS?
- D
  Dustin DeckerSep 23, 2025
  Excessive noise from your Hotsy Pressure Washer's pump can be due to: * **Air in the suction line:** Check the water supply and connections on the suction line. * **Broken or weak inlet or discharge valve springs:** Check and replace if necessary. * **Foreign matter in valves:** Check and clean if necessary. * **Worn bearings:** Check and replace if necessary. * **Excessive temperature of liquid:** Reduce the liquid temperature to below 75°C (160°F).
P
Patricia CarterNov 21, 2025
Why is the operating pressure low on my Hotsy 1710 SS Pressure Washer?
- R
  Robert RodriguezNov 21, 2025
  Low operating pressure in your Hotsy Pressure Washer can stem from several causes. It may be due to a faulty pressure gauge, in which case you should install a new one. Insufficient water supply can also be the culprit; try using a larger supply hose and cleaning the filter at the water inlet. Other potential causes include an old, worn, or incorrect spray nozzle (match the nozzle number to the machine or replace it), belt slippage (tighten or replace the belt), plumbing or hose leaks (check and retape with Teflon tape), worn pump packing (install a new kit), fouled or dirty inlet/discharge valves (clean them), worn valves (replace with a valve kit), obstruction in the spray nozzle (remove it), a leaking pressure control valve (rebuild or replace it), or insufficient power supply (check th...
K
Keith WillisSep 12, 2025
Why won't my Hotsy Pressure Washer system stop?
- L
  luis74Sep 12, 2025
  If your Hotsy Pressure Washer system will not stop, it is possible that the pressure switch is faulty (check, clean, or replace it) or the timer is faulty (check and replace it).
S
Stacie CarrilloSep 8, 2025
Why does the motor strain under load on my Hotsy Pressure Washer?
- M
  Marissa AdamsSep 8, 2025
  If your Hotsy Pressure Washer's motor strains under load, it could be due to a faulty motor (send to the nearest Baldor repair center), an incorrect spray nozzle (install the proper nozzle size as indicated on the serial plate), or an obstruction in the spray nozzle (remove the obstruction).

Hotsy 1710 SS Specifications

General

Brand	Hotsy
Model	1710 SS
Category	Pressure Washer
Language	English

Related product manuals

Preview: Hotsy 1710

Preview: Hotsy 1720

Preview: Hotsy 1700 Series

Hotsy 1700 Series

Preview: Hotsy 1260SS