HP 382 - Page 104

FINAL TRIM SIZE : 7.5 in x 9.0 in
6
Before Y
ou
Begin:
First
make
a
note
of
the
tap
e
driv
e
mo
del
and
its
hardw
are
address
(SCSI
bus
address)
so
that
y
ou
will
b
e
able
to
iden
tify it
later.
DDS
Driv
eMo
del:
Bus
Address:
1.
Log
in
as
root
.
2.
Run
SAM b
yt
yping the
follo
wing:
$
/usr/bin/sam
T
o
get
help
in
SAM,
pressing
the 4
f1
5
k
ey
giv
es
y
ou
context-sensitiv
e
information
for
the
ob
ject
at
the
lo
cation
of
the
cursor.
3.
Highligh
t
and
select
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
Peripheral
Devices
->
4.
A
t
the
next
screen
highligh
t
and
select
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Tape
Drives
->
5.
The
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Tape
Drive
Manager screen
lists
what
tap
e
devices
are
connected,
including y
our
new
device.
Highligh
t
that
device.
6.
F
rom
the
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
Actions
men
u,
c
ho
ose
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
Add...
.
A
message
screen
giv
es y
ou the
hardware
steps for
adding
the
tap
e
driv
e.
Activ
ate
N
N
N
N
N
N
N
N
OK .
7.
A
conrmation
screen
indicates
whether
an
y
related
device
driv
ers
needed
to
b
e
added
to
the
k
ernel.
Activ
ate
N
N
N
N
N
NN
NN
NN
Yes
or
press
4
Return
5
.
8.
If
y
ou
needed
to
add
a
device
driv
er,
y
ou
will also
need to
create a
new
k
ernel and
(ev
en
tually)
reb
o
ot
the
system.
Select
from
the
men
u
on
the
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Create a
New Kernel
screen whether
you
wan
tto
create
the
new
kernel
no
w,
later,
or
cancel
the
prop
osed
mo
dications.
(Make
sure
y
our
choice has an asterisk placed b
yit,b
y pressing
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
NN
N
Return while that line is
highligh
ted.) Activate
NNNNNNNN
OK
to conrm y
our c
hoice of action.
9. Y
ou will next b e giv
en a c
hoice of whether to install the
new kernel no
w
or later. If y
ou mo
v
ethe k
ernel in
to place no
w, the system will also
rebo ot. If y
ou c
hoose to do it later, y
ou can then mo
ve the new
kernel,
/etc/conf/dfile.SAM to /hp-ux and rebo ot. Y
ou should also
move
/etc/conf/dfile.SAM to /etc/conf/dfile at the same time.
6-26 Configuring HP-UX for Printers and Drives