HP 382

FINAL TRIM SIZE : 7.5 in x 9.0 in
6
5.
F
rom
the
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
Actions
men
u,
select
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
Add
a
Floppy
Disk
Drive...
.
Y
ou
will
see
a
list
of
un
used
disks,
including
the
new
one
y
ou
ha
ve
connected.
6.
Cho
ose
the
line
identifying
the mo
del of
the new
disk.
If
the
device
y
ou ha
ve
connected do
es not
app
ear
on
the
list:
a.
Chec
k
y
our
hardw
are
connections,
and
mak
e
sure
that
the
device
is
turned
on
.
b. Activ
ate the
button
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
Device Missing
,and
y
ou
will
b
e
giv
en
the
follo
wing
options:
i. Ha
ve
SAM
rescan
the
system
for
the
device.
If
y
ou
ha
v
e
connected
the
device
after starting
SAM, y
ou should
activate
N
N
N
N
N
N
N
N
N
N
N
Yes
.
Otherwise,
activate
N
N
N
N
N
N
N
N
No .
ii.
Resp
ond
to
the
conrmation
screen
regarding
whether
the
device
is
connected
and
po
wered
up.
iii.
Resp
ond
to
the
conrmation
screen
regarding
whether
additional
device
driv
ers
are
needed.
iv. Y
ou
will
b
e
giv
en
an
information
screen
suggesting
things
to
try
if
the
device
still
cannot
b
e
found.
7.
After
y
ou
highligh
t
the
device,
note
that
the
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Initialize
disk
button
is
toggled
on
(the
default).
Activ
ate
this
button
to
turn
it
o if
you
do not
wish
to
initialize
a
disk
(or
if
the
disk
is
preformatted).
8.
Activ
ate
NN
N
N
N
N
N
N
OK
when
y
ou
ha
v
e
nished with
this form.
9.
A
\Messages"
Bo
xapp
ears, rep
orting the
progress
of
the
task.
When
the
task
is
nished,
activ
ate
N
NN
N
N
N
N
N
OK
.
10. Exit SAM. (SAM copies
your original
/etc/checklist to
/etc/checklist.old ).
Configuring HP-UX for Printers and Drives 6-13